Epoxy Paints & Primers

Paints & Coatings

Epoxy Primers are formulated for ESD floor coating compatibility.

October 31, 2014

As high-build, solvent-free system intended for use where odors/VOCs are unacceptable, light grey 46062 Statguard provides self-leveling/penetrating epoxy primer for concrete floors. Medium viscosity/100% solids product offers coverage of ~200 ft²/gal. As 2-component, catalyzed, water-based epoxy suited for use as primer or topcoat for concrete, metal, and wood, light grey 46063 Statguard adheres to green concrete and exhibits abrasion and chemical resistance. Coverage is ~320 ft²/gal. Read More

Adhesives & Sealants, Paints & Coatings

ESD Floor Finish enhances industrial environment safety.

August 28, 2013

Created for industrial areas and open area environments requiring static protection, EpoxyStyle ESD 2-part epoxy floor finish becomes dry to touch within 5–7 hr after application and is ready for traffic 10–12 hr after application. Chemical- and abrasion-resistant product complies with Ozone Transport Commission and California VOC regulations, may be installed over old VCT and concrete, and provides uniform matte finish; gloss can be attained when used with DuraShield ESD finish. Read More

Paints & Coatings

Static Dissipative Paint meets FDA requirements.

January 25, 2011

Available in white and off white, Static Paint® resists oils, grease, foodstuffs, and detergents. Two-part epoxy system is water-resistant upon drying and can be applied by brush or spray. Supplied in 1 and 5 gallon kits, paint can be used on walls, floors, steel handles, railings, and various equipment used in food processing plants, restaurants, hospitals, schools, warehouse facilities, labs, or anywhere FDA-compliant antistatic paint for direct food contact is necessary. Read More

Adhesives & Sealants, Paints & Coatings, Architectural and Civil Engineering Products

Water-Borne Epoxy Coating creates fast-drying floor finish.

July 14, 2008

With mix ratio of 4A:1B, Monomid(TM) Epoxy Flooring System forms cleanable, high-gloss finish. It offers 5 mils DFT in one coat when applied over Monomid Clear Sealer and can be applied over various other primers for application on steel. Solution supports addition of anti-slip aggregate or sand and also offers moisture resistance. In 3 hr at 77ºF, coating dries to touch to form abrasion- and chemical-resistant finish. Use is suited for industries requiring low odor and VOC levels. Read More

Paints & Coatings, Materials & Material Processing

Epoxy Primer is designed for wet-on-wet spray application.

June 12, 2008

Promoting corrosion resistance over cleaned and treated steel, Spectracron 560 suits short wet-on-wet application windows when topcoated with Spectracron 2K polyurethane enamels; polyurethane topcoat can be applied directly over this primer 10-15 minutes after application. Formulated with VOC less than or equal to 3.5 lb/gal and less than 0.17 lb HAPS/gal, this 2-component, chrome-free primer adheres to cleaned G90 galvanized steel and aluminum as well as fiberglass substrates. Read More

Paints & Coatings

Epoxy Primer meets VOC requirements.

October 20, 2005

Enviroline 58HS enables users to hold surface preparation for up to 90 days while still meeting VOC requirements. Suited for application on interior or exterior steel, concrete, and masonry surfaces, high-solids product has less than 250 g/l VOCs. Applications include large tanks requiring surface preparation and situations where humid environments exist. Read More

Paints & Coatings

Epoxy Primer provides cure for green concrete.

June 9, 2005

Dual-component, water-based Prime-A-Seal IV 4350(TM) cures, seals, and primes concrete in one application. It maintains freshly poured slab's water content throughout curing process, allowing concrete to reach full strength. Promoting hydration, primer minimizes shrinkage cracking as concrete dries. Chemical-resistant primer protects surface against water, oil, salts, and other contaminants, while matte finish acts as stand-alone finish sealer. Read More

Adhesives & Sealants, Paints & Coatings

Water-Based Epoxy suits industrial/marine applications.

June 30, 2003

Fast Clad(TM) DTM, single-coat, direct-to-metal epoxy finish, provides high film build in one coat of 4-6 mils dry film thickness. Product dries to tough gloss finish, providing corrosion and chemical resistance as well as weathering protection. Applied at 77ºF, it dries to touch in 45 min and is dry to handle in 4 hr. Low-odor coating meets VOC and HAPS requirements, cleans up with water, and can be used directly over prepared steel. Read More

Paints & Coatings

Coating System provides zinc primer, epoxy, and urethane.

November 22, 2002

Moisture-cured urethane MC 104, with zinc-dust additive, cures by reacting with moisture in air. It is applicable in shop or field by spray or rolling. With high solids content (82%), CM 15 ivory-colored epoxy is suitable for spray applications. It offers some internal flex to allow for substrate expansion/contraction. Gloss white Acrylic Poly 2-part acrylic polyurethane topcoat offers high gloss, UV protection, and abrasion resistance. Read More

Adhesives & Sealants, Paints & Coatings

Epoxies have no hazardous air pollutants.

November 5, 2002

Steel Plus epoxies provide packaging and processing machinery with resistance to harsh CIP sanitation and corrosive chemicals, and are impervious to high-pressure washdown and other severe factory conditions. They have no odor and can be applied to steel, galvanized steel, tin, and aluminum. Epoxies are quick drying, resistant to alkalines and acids, and available in 1 or 5 gal sizes. They can be applied by brush, roller, air-atomized, air-less or hot spray. Read More

Paints & Coatings

Coatings rapidly return bridges to service.

October 31, 2002

Single-coat ExpressTech Fast Clad(TM) Urethane topcoat dries in 30 min. Fast Clad(TM) FD Epoxy is a 2-component, polyamide epoxy that can be applied as high-build coating, providing up to 6-8 mils DFT in single application to marginally prepared surfaces. It is VOC-compliant at 340 g/L. Fast Clad(TM) Zinc primer can be recoated in 2 to 3 hrs. Reinforced film offers resistance to topcoat bubbling, dry spray, and mudcracking. Read More

  • 1