Schutte & Koerting    Trevose, PA 19053
Apr 09, 2013 Unlike potentially hazardous motor-driven devices, S&K Gas Jet Compressors are ejectors that utilize jet of high-pressure gas as operating medium to entrain low-pressure gas, mix the two, and discharge at intermediate pressure. Gases can be steam, air, propane, or others. Compressors are suitable for use in process, paper, petroleum, power, gas and other industries to circulate steam, boost low-pressure steam, and to mix, transfer, and compress gases.

Tamturbo Oy    Tampere 33100  Finland
Apr 09, 2013 Featuring direct drive from high-speed motor to turbo impeller, and Active Magnetic Bearing that removes physical contact between parts, Air Turbo Compressors minimize wear compared to conventional ways of producing oil-free air. Units save energy and eliminate need to change and dispose of oil filters. In addition, capacity control method extends efficient control range of turbo compressors by dozens of percentage points, lowering electricity bills.

GE Co.    Southfield, MI 48034
Feb 05, 2013 Featuring one impeller, 2 magnetic bearings, and no split parts, single-stage Integrated Compressor Line (ICL) is designed for low-pressure ratio (1.1–1.4) applications. Design minimizes electric power consumption and offers full access to critical components. Utilizing centrifugal compression, electric motors, and variable speed drive, integrated system offers power range of 2–15 MW, design inlet pressure of 20–80 bar, discharge pressure up to 120 bar, and max speed of 18,000 rpm.

BITZER US Inc.    Flowery Branch, GA 30542
Dec 18, 2012 With ESEER (European Seasonal Energy Efficiency Ratio) of over 5, CSV series intelligent compact screw compressor meets requirements of EMC directive. Variable speed with integrated frequency inverter maximizes energy efficiency, while refrigerant-cooled electronics promote operational reliability and maintenance-free operation. Used in chillers for air conditioning systems, in heat pumps, and in industrial and process cooling, product communicates with master control via Modbus.

Thomas Products Division    Sheboygan, WI 53081
Dec 17, 2012 Designed for handheld gas and leak detection warning devices, 1010 Series has been tested for 4,000 hours of nonstop operation. Units feature sealed air path for contamination-free analysis and restart option at low temperatures for use in cold environments. Low inductance level and stall current allow for compliance with intrinsic safety requirements. Weighing just .03 lb, pumps provide max continuous pressure rating of 8.7 psi and max vacuum to 14.8 in.Hg.

Gardner Denver    Quincy, IL 62301
Oct 23, 2012 Manufactured with die-cast aluminum components, 319 Series Oil-less, WOB-L® Piston DC Pump and Compressor feature corrosion-resistant e-coated exterior finish, stainless steel inlet valve, thermally protected motor, and inlet filter/exhaust muffler. RoHS-compliant units provide up to 150 psi max intermittent pressure and 93% local barometer of max vacuum. Also available with 12 and 24 Vdc motor and dryer/solenoid, series is suited for air suspension, air doors, air horns, and air brakes/clutches.

Kaeser Compressors, Inc.    Fredericksburg, VA 22404
Oct 15, 2012 Combining rotary screw airend and Mercedes Benz diesel engine, Mobilair M350 provides compressed air with minimal emissions and fuel consumption for construction sites and other applications such as demolition, sand blasting, and sprinkler irrigation. Towable compressor features anti-frost valve, SCR catalytic converter, and viscous fan clutch controlled via Sigma Control Mobile™. Options include various pressures, skid-mounting, and air treatment for cool, dry air.

Emerson Climate Technologies, Inc.    Sidney, Oh 45365-0669
Sep 04, 2012 Suited for 1-4 hp applications, Copeland Scroll(TM) ZSKA Compressor covers evaporating temperatures from -25 to 45°F and is compatible with variety of refrigerants, including R-404A, R-507, R-134a, R-407A/C, and R-22. Axial and radial scroll compliance optimizes liquid handling capability, while hermetic design minimizes leak potential. Compressor is recommended for walk-in refrigerators and freezers, as well as soft serve machines and frozen beverage machines.

Thomas Products Division    Sheboygan, WI 53081
Aug 27, 2012 Picolino Rotary pump and compressor are designed for applications such as medical, vacuum lifting, laboratory, air sampling, sewage aeration, and printing. Pulsation-free pump comes in 2 configurations: DTE (pressure), with inlet silencer, pressure relief valve, and outlet tube connector, and VTE (vacuum), with outlet silencer and tube connector. Respectively, max ratings for flow, pressure, and vacuum are 2.06-7.6 cfm, 14.5 psig, and 25.1 in. Hg.

Kaeser Compressors, Inc.    Fredericksburg, VA 22404
Jul 19, 2012 Providing 900 cfm at 125 psig, 288 hp Mobilair(TM) M250 features Mercedes-Benz diesel engine and is designed for facilitated towing and maneuverability. Standard version weighs less than 7,000 lb, anti-frost valve maintains optimum operating temperature while also preventing tool freeze-up, and fuel tank size enables extended operation. Options include pressures to 205 psig and air treatment to meet demands of applications such as concrete repair.

Kaeser Compressors, Inc.    Fredericksburg, VA 22404
Jul 05, 2012 Equipped with 3-cylinder, 21 hp Kubota diesel engine that complies with Tier 4 emissions standard, Mobilair(TM) M27 has rotomolded polymer canopy that is scratch- and dent-resistant, and heavy-duty chassis for further protection from elements and corrosion. Come winter, anti-frost valve maintains optimum operating temperature. Mobilair(TM) M27 features tool box for storage, and is available as skid-mounted utility model for cross mounting on service vehicles.

Kaeser Compressors, Inc.    Fredericksburg, VA 22404
Jun 25, 2012 Employing 3-cylinder, 21 hp Kubota diesel engine compliant with Tier 4 emissions standards, Mobilair(TM) M27 has maneuverable design and rotomolded polymer canopy that resists scratches and dents. Heavy-duty chassis offers protection from elements and corrosion, while anti-frost valve maintains optimum operating temperature in winter conditions. Tool box is supplied as standard for storage, and compressor is available as skid-mounted utility model for cross mounting on service vehicles.

Atlas Copco Compressors, Inc.    Westfield, MA 01085
Jun 22, 2012 Combining oil-injected screw element and load/unload regulation, 10 hp Model GX 7 EP is suitable for small industrial applications and can be installed directly into workplace. Unit discharges cooling air from top, which permits placement in corner against wall. Available in floor- or tank-mounted variants, Model GX 7 EP features optional integrated dryer.

Next Generation Power Engineering, Inc.    Jacksonville, FL 32246
Apr 24, 2012 Powered by 4-cylinder, turbocharged Kubota industrial diesel engine, Gen-Air-Ator combines 35 kW Stamford Newage diesel generator with 10 hp Hydrovane rotary vane compressor producing 35 cfm at 150 psi. Running both components at 1,800 rpm as one rigid assembly minimizes vibration and noise, and eliminates need for heavy mounting frame. Measuring 87 x 23 x 36 in., Gen-Air-Ator is suited for spray foam and coatings operations.

Emerson Climate Technologies, Inc.    Sidney, Oh 45365-0669
Feb 03, 2012 Serving stand-alone and parallel systems with large (7.5-15 hp) refrigeration requirements for low- to medium-temperature applications, Copeland Scroll® K5 refrigeration compressor incorporates 2 features that promote system efficiency. Variable volume ratio technology optimizes low-condensing performance, while vapor injection capability maximizes capacity at low set points without adding more/larger compressors. CoreSense(TM) technology allows on-site/remote diagnostics to help reduce downtime.

Kaeser Compressors, Inc.    Fredericksburg, VA 22404
Dec 21, 2011 Offered in 250 and 300 hp models, ESD series provides flows from 816-1,522 cfm and pressures to 217 psig. One-to-one direct drive design includes efficiency-oriented drive motor with three PT 100 temperature sensors. All models come with Sigma Control 2 intelligent compressor control and variable-speed fan for fluid cooler. Latter helps conserve energy by adjusting to cooling demands, while removable panel and 5 access doors optimize maintenance accessibility.

Miller Electric Mfg. Co.    Appleton, WI 54912 1079
Mar 18, 2011 Equipped with 27 hp Kubota diesel engine, EnPak® Air Power 40 eliminates need for hydraulically driven standalone or under-hood compressors, and integrates seamlessly into truck's electrical and fuel systems, allowing field service personnel to run air and power tools off one unit with truck turned off. System includes Air Pak(TM) 40 variable-speed rotary screw air compressor, rated 40 cfm at 100 psi with 175 psi max pressure. It also delivers 6,000 W of generator power for welders and power tools.

Burckhardt Compression AG    Winterthur   Switzerland
Jan 19, 2011 Accommodating demands for rod load up to 335,000 lb and power up to 42,100 hp, Process Gas Compressor API 618 range covers performance requirements of large plants in hydrocarbon processing industry. Quality of compressor components and valves promote availability and extend meantime between overhaul. Applications include refinery and petrochemical/chemical industry as well as industrial gases and gas transport/storage.

Boge American, Inc.    Powder Springs, GA 30127
Jan 07, 2011 Available as 220 or 600 psi compressor, Boge SR Booster Series provides effective free air deliveries from 33-258 cfm with rated power range of 7.5-25 hp. Oil-lubricated units take pre-compressed and already treated compressed air from existing network or standard pressure compressor and boost it to desired higher pressure. Integrated oil level monitor assures operational safety, while pre-filter optimizes intake air quality and prevents contamination damage in aggressive environments.

Gardner Denver Nash    Trumbull, CT 06611
Nov 23, 2010 Designed to meet process industry requirements, Vectra XL 950 offers vacuum pump operation to 28.5 in. HgV and compressor operation to 30 psig. Single point inlet and discharge connections eliminate need for manifolds, which facilitates process piping and conserves space. Additional features include O-ring sealing, oil lubricated bearings option, and either ductile iron or all-316L stainless steel construction.