ThomasNet News Logo
Sign Up | Log In | ThomasNet Home | Promote Your Business

ASTM Standards Revision clarifies thickness tolerances for steel sheets.

Print | 
Email |  Comment   Share  
February 4, 2010 - ASTM International Committees A01 on Steel, Stainless Steel, and Related Alloys and A05 on Metallic-Coated Iron and Steel Products approved revisions to two ASTM standards that will clarify thickness tolerances for uncoated and coated steel sheet products. Committees A01 and A05 have moved 3/8-in. [10 mm] tables from body of A568/A568M and A924/A924M to Supplementary Requirements sections, and 1 in. edge distance tables are now the default applicable thickness tolerances.

Thickness Tolerances Clarified in Revision to ASTM Steel Sheet Standards


(Archive News Story - Products mentioned in this Archive News Story may or may not be available from the manufacturer.)

ASTM International
100 Barr Harbor Dr., Box C700
West Conshohocken, PA, 19428-2959
USA



Press release date: February 1, 2010

W. CONSHOHOCKEN, Pa., -ASTM International Committees A01 on Steel, Stainless Steel and Related Alloys and A05 on Metallic-Coated Iron and Steel Products recently approved revisions to two ASTM standards that will dramatically clarify the thickness tolerances for both uncoated and coated steel sheet products. The standards are: A568/A568M, Specification for Steel, Sheet, Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for; and ASTM A924/A924M, Specification for General Requirements for Steel Sheet, Metallic-Coated by the Hot-Dip Process.

Previously, standards for these products included two sets of tolerance tables for each product, neither of which was the default. Purchasers were required to decide which set of tables applied to their purchase orders. With the approval of these standards in November 2009, all general steel sheet and product specifications have default thickness tolerance tables with limits that can be used worldwide. In the past, each set of thickness tolerance tables differed not only in tolerance limits but also in how close to the edge of the sheet these limits applied.

Thickness fall-off close to the sheet edge is a natural phenomenon that occurs during hot and cold rolling. On purchase orders, the buyer was required to specify which set applied. Buyers needing to protect a minimum thickness closer to the edge generally invoked the 3/8-in. [10 mm] edge distance tables even though they have less restrictive tolerances.

Committees A01 and A05 have moved the 3/8-in. [10 mm] tables from the body of A568/A568M and A924/A924M to the Supplementary Requirements sections of these documents. The 1-in. [25mm] edge distance tables are now the default applicable thickness tolerances unless the supplementary 3/8-inch [10 mm] tables are called out on the purchase order.

The Ordering Information section of each product specification has been revised to direct purchasers to the supplementary tables in the respective general specifications.

These revisions make available thickness tolerances much clearer, as there is only one set of tables in the body of the specifications. Because these tables are now the equivalent of any in the world, requests for "one-half ASTM thickness tolerance" should decline. On the other hand, users who need product purchased to the 3/8-in. [10 mm] edge distance can still obtain their requirements by invoking the Supplementary Requirements section of the specifications.

To purchase ASTM standards, visit www.astm.org and search by the standard designation number, or contact ASTM Customer Relations (phone: 610-832-9585; service@astm.org). ASTM International is one of the largest international standards development and delivery systems in the world. ASTM International meets the World Trade Organization (WTO) principles for the development of international standards: coherence, consensus, development dimension, effectiveness, impartiality, openness, relevance and transparency. ASTM standards are accepted and used in research and development, product testing, quality systems and commercial transactions.

ASTM Committee A01 Next Meeting: May 17-20, St. Louis, Mo.

ASTM Committee A05 Next Meeting: May 16-18, St. Louis, Mo.

www.astm.org
Print | 
Email |  Comment   Share  
Contacts: View detailed contact information.


 

Post a comment about this story

Name:
E-mail:
(your e-mail address will not be posted)
Comment title:
Comment:
To submit comment, enter the security code shown below and press 'Post Comment'.
 



 See related product stories
More .....
 See more product news in:
Services
 More New Product News from this company:
ASTM Workshop to address additives in biomedical polymers.
Oil Training Course examines sampling, testing, evaluation.
Radiant Barrier Systems Standards approved by ASTM committee.
Training Course addresses hazards in oxygen systems.
More ....
| Featured Manufacturing Jobs
 Other News from this company:
ASTM/NIBS Workshop on Building Science Education in North America
Fatigue and Fracture of Metallic Medical Materials and Devices
ASTM International Compilation on Silica and Associated Respirable Mineral Particles
Guidance for Potential Solar Photovoltaic Investors to Be Provided in Proposed ASTM Standard
Test for Sustained Air Performance of Central Vacuum Cleaning Units Approved as ASTM Standard
More ....
 Tools for you
Watch Company 
View Company Profile
Company web site
More news from this company
E-mail this story to a friend
Save Story
Search for suppliers of
Trade Associations


Home  |  My ThomasNet News®  |  Industry Market Trends®  |  Submit Release  |  Advertise  |  Contact News  |  About Us
Brought to you by Thomasnet.com        Browse ThomasNet Directory

Copyright © 2014 Thomas Publishing Company. All Rights Reserved.
Terms of Use - Privacy Policy



Error close

Please enter a valid email address