Deflection Elbow Kits for Silo Top Fill Lines
Bethlehem, PA---New Smart Elbow® Deflection Elbow Kits from HammerTek® Corp allow direct replacement of silo top elbows and piping/tubing subject to abrasive wear, with all preparation done safely at ground level. Each kit contains all components required to replace failing elbows, including two Smart Elbow® deflection elbows and all necessary piping/tubing, connectors and gaskets. All can be...Read More »
New Pneumatic Conveying Elbows Offered in Cast Iron or Optional Stainless Steel
Gathers conveying air or gas in a round, rotating deflection zone that virtually eliminates destructive particle impact with the elbow wall. Effective for conveying abrasive, heat-sensitive and other powders, pellets, flakes and slurries. Available in seven different sizes to suit a wide range of material properties and throughput requirements.Read More »
Cold Expansion Pex Drop Ear Elbow consists of lead free brass.
F1960 Cold Expansion Pex Drop Ear Elbow is available in ½ (FIP) x ½ in. Pex size. Compliant to Safe Drinking Water Act (SDWA), unit features three ears.Read More »
ICE Series Inside Corner Elbow enables installations in inaccessible locations.
Used in ceiling installation for communications and power, hard-to-reach 90-degree bends under decks and below floors, ICE Inside Corner Elbow allows for multiple conduit runs which are to be installed in parallel without interference while accessing elbow’s cover. Providing smooth pulling surface for conductors to glide against, product enables for easy access when adding or removing cables...Read More »
Everything You Need to Know About Cold Chain/Temperature Controlled Packaging
This ebook provides an overview of everything you need to know about cold chain and temperature-controlled packaging.Read More »
Replacement Metric Flat Face Fittings
Replacement Fittings for Most Foreign Manufactured Equipment Mentor, OH, December 27, 2016 – Malone Specialty Inc., a quality manufacturer of industrial hose and hose fittings for over 30 years, is now manufacturing and stocking standard Metric Flat Face Fittings. Steve Malone, President of Malone Specialty Inc. stated, “For years we have been providing metric fittings and adapters use d by...Read More »
Pulling Elbows make wiring pulls at right angles.
Manufactured in CF8M (316 SS), pulling elbows are designed for use with rigid conduit.These products, which make wiring pulls at 90° bends in conduit system, can assist in instances of sharp bends and allow straight pull in either direction. Each pulling elbow comes with Type 316 SS cover, neoprene gasket, and Type 316 SS screws.Read More »
Viega's New 45-Degree Elbows For Viega PEX Press Systems provide flexibility for larger tubing.
Available in 1 1/2 and 2 sizes, Viega PEX Press 45-degree elbows feature Viega's patented Smart ConnectR feature, which allows water to flow past an unpressed fitting. Suitable for use in commercial applications, Viega PEX Press is molded from Radel-RR, a superior plastic material. Factory assembled with attached stainless steel sleeves with three view holes, 45-degree elbows can be used with all...Read More »
T&B® Fittings meet ASTM A-321 and SA-312 standards.
Suitable for food and beverage market, T&B’s 45- and 90-degree elbows and 12-inch nipples, comes in both Type 304 and Type 316 stainless steel. Resistant to extreme corrosion and chemicals, Type 304 stainless steel has five times the service life and Type 316 stainless steel eight times the service life. Presented with- National Pipe Thread for easy installation, stainless steel conduit and...Read More »
Capped Elbows are designed for use in hazardous locations.
Available for rigid wiring systems in hazardous locations, Malleable Iron Capped Elbows come in -½, -¾,- 1, and 1 -¼ in.- trade sizes and are UL listed for Class I, Group C/D; Class II, Group E/F/G; and Class III environments. These explosionproof products, which- feature malleable iron construction with- bright electro-zinc finish, provide pull-in capacity and 90-Read More »
Connectors and Plugs serve commercial and municipal applications.
Used with Viega PEX Press system,- PEX Press test plugs (3/8–1 in., 1 -¼ in.,- and 1 -½ in.) have Smart Connect-® feature. Also made of Radel R, 45-Read More »
Precision Machined Parts for High Tech Applications
For precision and value that sets the standard for quality and craftsmanship, EGS Production Machining is the source for precision and value. Our extensive capabilities and dedication to customer service allow us to deliver the optimal manufacturing solution. See our video to learn more.Read More »