Split Seals are engineered for pumps and mixers.

Press Release Summary:

Model PSS III pressurized split seal offers 300 psig vacuum pressure capability in normal operating conditions and successfully operates after experiencing excursions up to 450 psig. Model features 0.060 in. TIR radial shaft run out capability and has allowable temperature range of 0-250°F. Series comes pre-assembled into drive and gland halves, and is suited for use in paper mills, wastewater treatment facilities, soda ash processing, and light chemical plants.

Original Press Release:

Flowserve Releases New PSS III Split Seal Addition to PSS Line Delivers Proven Performance and Ease-of-Maintenance

Dallas, Texas, USA - May 22, 2007 - Flowserve Corporation, a global provider of fluid motion and control products and services (NYSE: FLS), announces the release of the PSS III, its next-generation single OD pressurized split seal. The enhanced PSS III adds new design features to improve performance, reliability and ease of installation and repair.

The PSS III split seal is designed for pumps and mixers. It is ideally suited for use in paper mills, wastewater treatment facilities, soda ash processing and light chemical plants.

"The release of the PSS III seal demonstrates the Flowserve philosophy of continuous improvement in split-sealing solutions," says Mark Fallek, vice president, marketing, Flow Solutions division. "Since the 1960s, the Flowserve line of PSS split seals has been consistently upgraded to meet the newest customer requirements in the process industries."

Easy Installation

Compared to competing split seals, replacement of the PSS III is fast and easy in difficult-to-service equipment applications. All fasteners and gaskets are captured in four major components, simplifying installation and greatly improving the likelihood of first-time installation success.

The pump and primary driver on the PSS III do not need to be completely dismantled during seal maintenance because the seal installs around the shaft and outside the seal chamber. Installation tools are included with the seal, and only one wrench is required for the gland bolts, further simplifying maintenance. Because PSS III seal faces are pre-assembled into the drive and gland halves, there is no need to handle the individual faces - reducing the risk of face damage.

Design Enhancements

The PSS III is designed with an industry-leading pressure capability for split seals - vacuum to 300 psig (21 bar) in normal operating conditions - and successfully operates after experiencing excursions up to 450 psig (31 bar). The allowable temperature range of the PSS III is 0 to 250 degree F (-18 to 121 degree C). Custom engineered designs of the PSS III meet even more rigorous demands.

Other enhancements to the PSS III include an improved seal drive and gland ring, which provide a greater axial holding power and result in the high-pressure rating of the seal. A 0.060-inch (1.5 mm) TIR radial shaft run out capability enables the PSS III to accommodate the most demanding mixer characteristics.

Proven Reliability

During PSS III development, Flowserve product managers received a record number of field trials requests. More than 200 field trials were conducted, in applications ranging from white water to screens in paper mills to high-concentration stock pumps above 3 percent stock.

The PSS III has already proven its performance in a variety of trial applications. At a plant in Wyoming, PSS III seals were installed in soda ash pumps and agitators with a low mean time between failure (MTBF). The PSS III design upgrades and higher pressure capabilities helped increase MTBF by more than 50%.

For additional technical information, contact Thomas Bennett, product manager, Flowserve Flow Solutions, by phone at +1 (269) 226-3499 or by e-mail at tbennett@flowserve.com.

About Flowserve Corp.

Flowserve Corp. is one of the world's leading providers of fluid motion and control products and services. Operating in 56 countries, the company produces engineered and industrial pumps, seals and valves as well as a range of related flow management services. More information about Flowserve Corp. can be obtained by visiting the company's website at www.flowserve.com.

More from Chemicals & Gases

All Topics