Software checks full-chip design manufacturability.
Share:
Press Release Summary:
InShape(TM) predicts accurate silicon shapes, enabling designers to perform DFM hotspot detection of catastrophic failures. This model-based Design Manufacturability Checker utilizes nonlinear optical transformation algorithm to detect potential manufacturing failures during physical design. Compact models encapsulate all necessary RET, OPC, mask, etch, and lithography effects on both device and interconnect, predicting accurate contours for entire chip from drawn layout within hours.
Original Press Release:
Clear Shape Announces InShape(TM) for Full-Chip Design Manufacturability Checking and Enabling eDFM
SANTA CLARA, Calif., Nov. 27 -- Clear Shape Technologies, Inc., a leader in variability-aware analysis and optimization solutions, today announced InShape, the first model-based full-chip Design Manufacturability Checker that predicts accurate silicon shapes, providing designers the ability to do fast, accurate DFM hotspot detection of catastrophic failures. Additionally, InShape's critical variation information is a required input for fast and accurate eDFM analysis and optimization across process window.
InShape utilizes a patent-pending, model-based, non-linear optical transformation algorithm that allows designers to quickly and accurately detect potential manufacturing failures during physical design that would otherwise be found after tape-out in mask or silicon. The compact models encapsulate all necessary RET, OPC, mask, etch and lithography effects on both device and interconnect, and predict accurate contours for the entire chip from drawn layout in a matter of hours.
InShape provides designer hotspot identification based on fab-designated criteria or Clear Shape's Litho Yield Sensitivity (LYS) metrics. The non- linear optical transformation algorithm also allows generation of automatic fixing guidelines that are input into the user's choice of third party physical design tools. InShape is easily integrated into current library, IP, custom analog and cell-based digital physical design flows.
"The fundamental change over the last few years is that the lithography roadmap is now fixed with 193nm and various RET/OPC techniques perhaps including immersion," said Dr. Yao-Ting Wang, Clear Shape's CTO and Chairman. "Yet the resolution problem continues to worsen and the actual shapes on silicon are progressively variant from ideal shapes in DRC-clean GDSII. This leads to catastrophic and parametric failures and lower than entitled performance. With Clear Shape's proprietary fast full-chip non-linear optical transformation algorithm, designers can now leverage accurate silicon shapes and optimize their designs before tapeout."
Semiconductor Companies and Foundries Select InShape
Clear Shape offers the only DFM product in its class qualified by TSMC. Several leading edge fabless and semiconductor chip companies including Qualcomm and NEC Electronics Corporation also have already validated InShape's accuracy and adopted it.
"Following a rigorous process to ensure accuracy, TSMC qualified Clear Shape's InShape as part of its DFM initiative," stated Ed Wan, senior director of design services product marketing for TSMC. "InShape is now qualified for all critical layers of TSMC's 65nm process technology and our DFM Data Kit (DDK) is ready for use."
"It had been a challenge to get accurate silicon contour information in a fast enough manner to confidently manage variability issues for our 90 nm designs," stated Takaaki Kuwata, GM for the Advanced Device Development Division, Technology Foundation Development Operations Unit of NEC Electronics Corporation. "After extensive joint work and evaluation we are satisfied with InShape based on its ability to provide accurate silicon contours across the entire chip in a matter of hours, using design layout information as input. Most importantly, we see the interconnect and device variability information that InShape produces with no extra overhead to be a required component for electrical DFM. We look forward to expanding the joint effort with Clear Shape for our 65 nm and 55 nm designs."
Importance of Model-Based Manufacturing Shape Predictions
At 65 nanometers, lithography, etch and CMP are factors in causing systematic manufacturing variations to surpass random variations as the prime limiters to catastrophic and parametric yield loss.
The interaction of the shapes within the optical proximity halo and the spatially partially-coherent lithography projection systems creates highly non-linear systematic variations at different process conditions that cannot be captured by rules or pattern matching. The consequence is that these systematic shape variations, dependent on specific layout shape context, result in predictable catastrophic errors such as necking (opens) and bridging (shorts). Furthermore, the shape variations of interconnect and gate have a non-linear impact on electric parameters such as timing, leakage power and signal integrity.
Traditional options to deal with manufacturing variation are no longer adequate at sub-90 nm:
1. Post-GDSII OPC uncovers printability problems that frequently require actual design changes when there is limited freedom after tape-out, making design closure unpredictable.
2. Running post-GDSII OPC tools during layout isn't feasible, because it takes days per layer to run a typical design through OPC and it is impractical to provide proprietary OPC-recipes to designers.
3. DRC alone is inadequate to prevent catastrophic yield loss due to systematic shape variations; additionally, DRC rules to address growing DFM issues become prohibitive in number and complexity.
4. Designers can restrict their design style to try to improve yield, but this leaves both area and performance on the table and underutilize expensive leading edge processes.
Only model-based predictive approaches that are not based on moving post- GDSII OPC tools to designer's desk are potentially fast enough to let designers uncover hotspots during design implementation and make real-time design adjustments to eliminate them.
InShape: Hierarchical full-chip hotspot detection during layout
InShape design manufacturability checker performs fast hierarchical full- chip silicon contour prediction across process window during design. InShape guides the designer to make changes only when there is a problem due to process-design interaction, rather than forcing a rigid design style through over-restrictive rules on polygon placement.
With a use model similar to DRC, designers run InShape on their layout to perform a model-based verification that complements DRC. InShape uses this GDS layout information, in combination with the fab technology files, to automatically produce a report flagging DFM hotspots such as opens and shorts, contact coverage, gate variability, and line-end pull-back in the designer's original layout.
InShape sorts the hotspots identified by type and criticality. It allows a fast analyze-fix-verify cycle by providing hotspot markers as well as ECO fixing guidelines that can be easily exported to 3rd party layout editors and/or place and route tools. InShape's fast contour prediction allows what-if analysis to be performed, and pre-checked blocks can be excluded by name or marker layer.
InShape's full-chip hotspot reports are generated in hours, with performance that is linearly scalable with the number of CPUs. InShape's capacity has been tested to a half billion transistors, and meets the accuracy criteria for certification by TSMC.
InShape also produces critical dimension (CD) reports that can be utilized by Clear Shape's OutPerform(TM) eDFM parametric analysis and optimization product.
Pricing and Availability
InShape pricing starts at $300,000 per master license per year. InShape is available on Linux platforms. Distributed Processing is also available at incremental pricing.
About Clear Shape
Clear Shape Technologies, Inc. is focused on delivering a complete Variability Platform that allows designers to control and optimize the parametric and catastrophic impact of systematic manufacturing variations. Clear Shape's products are based on patent-pending technologies enabling designers to efficiently achieve entitled performance and yield. Clear Shape is backed by top-tier venture investors that include USVP, Intel Capital and KT Ventures (KLA Tencor). The company is headquartered at 3255-3 Scott Blvd, Suite 102 Santa Clara, Calif. 95054. For more information, visit www.clearshape.com or call +1 (408) 833-7130.
InShape and OutPerform are trademarks of Clear Shape.
CONTACT: Gloria Nichols of Launch Marketing, +1-650-851-6919, gloria@launchm.com; or Nitin Deo, Vice President, Marketing and Business Development of Clear Shape, +1-408-960-1578, nitin@clearshape.com
