Rohde & Schwarz Takes Wireless Device Precompliance Testing into the Lab with Automated Tests as in Large RF Test Chambers

In wireless device precompliance testing, the compact R&S DST200 RF diagnostic chamber from Rohde & Schwarz now automatically sets the equipment under test (EUT) to the required position. The new options make the R&S DST200 the only RF test chamber on the market that enables OTA performance and RSE testing of wireless devices such as smartphones right on the lab bench. Test results are comparable with those obtained with large RF test chambers and are used for product optimization during the design phase - providing an ideal preparation for final compliance testing

Munich, - Rohde & Schwarz has added three new options for its compact R&S DST200 RF diagnostic chamber: the R&S DST-B160 automated 3D positioner, the R&S DST-B210 cross-polarized test antenna and the R&S DST-B270 communications antenna. The new options significantly speed up precompliance testing of wireless devices, allowing automated test sequences to be performed on the lab bench so that developers no longer require constant access to large RF test chambers.

The R&S DST200 RF diagnostic chamber together with the R&S CMW500 wideband
communication tester from Rohde & Schwarz now enables fast, reproducible over-the-air (OTA) testing in accordance with the Cellular Telecommunications Industry Association (CTIA) test specification. In conjunction with an R&S ESU EMI test receiver from Rohde & Schwarz, the new options make it possible to carry out radiated spurious emission (RSE) measurements quickly and easily with the R&S DST200. These test setups are ideal for wireless device design optimization. Developers can compare the results generated with the R&S DST200 with the results obtained with larger RF test chambers, since similar test sequences are used in these chambers. The results generated with the different types of chambers exhibit a high level of correlation, differing from each other by no more than a few decibels. Using this solution, network operators can now perform conclusive qualification measurements on smartphones, for example, without the need to access large RF test chambers.

The new R&S DST-B160 automated 3D positioner uses servomotors to position the EUT in any orientation required for OTA measurements, eliminating the need for time-consuming manual positioning. The R&S AMS32 OTA performance measurement software supports all cellular standards, including LTE MIMO, as well as WLAN and Bluetooth, plus it enables assisted GPS (A-GPS) performance measurements. In RSE measurements, the system automatically determines the EUT position with the highest RF emission, and then uses the R&S EMC32 software to perform EMC measurements in accordance with ETSI EN 301 908 (for W-CDMA) or a similar standard.

The R&S DST-B160 automated 3D positioner is made of a special, low relative permittivity material for RF applications so as to minimize its effect on the measurements. The servomotors are accommodated in an RF shielded compartment at the bottom of the R&S DST200. The user attaches the EUT to a removable holder, which is snapped into a bracket so that the EUT is positioned at the center of the R&S DST-B160. The EUT can be rotated independently about two axes into any desired position relative to the test antenna.

The new R&S DST-B210 cross-polarized test antenna is designed for testing wireless devices and chipsets with the R&S DST200. The antenna has a wide frequency range of 300 MHz to 12 GHz, ensuring that all harmonics will be covered when performing RSE measurements. The R&S DST-B270 linear-polarized communications antenna has a frequency range of 700 MHz to 18 GHz and provides a stable connection between the EUT and the test receiver while the EUT is being rotated.

The new options for the compact R&S DST200 RF diagnostic chamber are now available from Rohde & Schwarz. For details, visit

Press contacts:
Europe (headquarters): Monika Roth, Phone: +49 89 4129 12232, E-mail:

North America: Chris Petrole, Phone: +1 410 910 7836, E-mail:

Asia Pacific: Wen Shi Tong, Phone: +65 6 307-0029, E-mail:

Contacts for readers:
Customer Support Europe, Africa, Middle East: Phone: +49 89 4129 12345

Customer Support North America: Phone: +1 888 837 8772, E-mail:

Customer Support Latin America: Phone: +1 410 910 7988, E-mail:

Customer Support Asia: Phone: +65 65130 488, E-mail:

Customer Support China: Phone: +86-800-810-8228 or +86-400-650-5896,

Rohde & Schwarz

Rohde & Schwarz is an independent group of companies specializing in electronics. It is a leading supplier of solutions in the fields of test and measurement, broadcasting, radiomonitoring and radiolocation, as well as secure communications. Established more than 75 years ago, Rohde & Schwarz has a global presence and a dedicated service network in over 70 countries. It has approx. 8400 employees and achieved a net revenue of Euros 1.6 billion (US$ 2.2 billion) in fiscal year 2010/2011 (July 2010 to June 2011). Company headquarters are in Munich, Germany.

More from Materials

All Topics