Jet Edge Helps University of Minnesota Solar Vehicle Project

Take Latest Car to Next Dimension with 5-Axis Waterjet

Waterjet Manufacturer Cuts Fiberglass Composite Parts for Solar Car Team

ST. MICHAEL, Minn. – Waterjet systems manufacturer Jet Edge, Inc. recently helped the University of Minnesota Solar Vehicle Project (UMNSVP) by waterjetting several fiberglass composite chassis components for the team's new car, "Eos."

St. Michael-based Jet Edge is one of several Minnesota companies helping the student solar car team design and manufacture its two-person Cruiser Class car that will compete in the 3-day Formula Sun Grand Prix track race at Circuit of the Americas in Austin, Texas, in July and the 3000 km (1877 mile) World Solar Challenge in Australia in October.

The 40-member student-run team has been working on Eos for a year and a half and plans to unveil it sometime in early July, said team engineer Jacob Herbers. Until then, all design improvements are being kept under wraps. 

Eos is the UMNSVP's 12th car since the project's inception in 1990.  The project has raced numerous times in both the American Solar Challenge and the World Solar Challenge.  Over the years, the project's teams have placed either first or second 15 times and have travelled to Canada, Australia, Japan, and Taiwan. The project has given students invaluable real world experience as they are responsible for designing, funding, building, testing, and racing each vehicle.  It also has helped advance solar technology by serving as an innovation test bed, and has helped advance electric motor technologies, paving the way for today's successful electric car companies.

The project has benefited from the tremendous support of Twin Cities businesses, noted Herbers, who recently completed his undergraduate degree in mechanical engineering.

"There are hundreds of different parts in the car, including the carbon composite outer shell, the carbon and fiberglass composite chassis panels, aluminum and steel mechanical components, solar cells, electric motors and controllers, lithium-ion batteries, electrical wiring, etc.," he explained. "Our project would be impossible without the help of local manufacturers, who have helped us with layups, laser-cutting, tube bending, CNC milling and lathing, heat-treating, soldering and waterjet cutting."

Herbers explained that the car's chassis components and other parts are cut from as light of material as possible to help the car achieve faster speeds.  The team's previous car topped out at 80 miles per hour.

"The finished weight is estimated to be 500 pounds," he said.  "Every added pound of weight on the car would cause us to have to drive slower in the race.

Jet Edge's role in the project was to cut 14 parts from a 0.53" thick composite material that consisted of a layer of fiberglass on either side of 0.5" thick aramid honeycomb core.  The waterjet manufacturer cut the parts in its St. Michael test lab, using its latest EDGE X-5® 5-axis waterjet cutting system. 

Prior to cutting the parts, Jet Edge's RD engineer Michael Wheeler and Machinist Brian Wallace worked with the team to create DXF files from 3D files supplied by the team.   They then used IGEMS waterjet CAD/CAM/nesting software to produce the complicated bevels and to create the CNC programs.  While the parts were already nested by the team, Wallace fine-tuned the nesting using IGEMS to save material.

"We cut the parts at 78,000 psi using a 0.010/0.030 orifice/nozzle combination," said Wallace.  "We used 0.4 pounds per minute of 80 grit garnet abrasive.  We cut the holes at 10 inches per minute and the external shapes at 60 inches per minute.  We adjusted the speed down appropriately for the bevels cuts.  We only had one sheet of material to work with, so we utilized our nesting software to get the most parts out of that sheet.  It took about 30 minutes to cut all 14 parts."

"This was first time I've cut a honeycombed composite material with the 5-axis," Wallace said. "It worked perfect. We probably could have cut the part without abrasive, but we didn't have a lot of material to experiment with, so I decided to use abrasive.  The material wasn't hard, but with the honeycomb and the bevels, you're cutting through open areas that interrupt the waterjet, and you are cutting through thicker and thinner material as it bevels."

To Herbers' knowledge, the team has always used waterjet to cut its composite components.

"It is very precise and ensures a good fit when we assemble the chassis panels," he said.

Herbers encouraged other students to get involved in the Solar Vehicle Project.  The UMNSVP is open to all University of Minnesota students, regardless of their area of study, he noted.  Members can have as much or as little involvement as they want, but everyone works on designing and manufacturing a part of the car and more experienced members hold leadership positions.

"It is very interesting to visit with local manufacturers and see their processes," said Herbers, who is pursuing a career that will allow him to use his knowledge to save energy and protect the environment.  "I've learned a lot about how to design parts for manufacturability, and have gotten to see firsthand how parts of different materials get made, which are things that mostly aren't taught in school, and will definitely help prepare me for a career in mechanical engineering."

About the University of Minnesota Solar Vehicle Project

The University of Minnesota Solar Vehicle Project is a student-run project that designs, builds and races solar vehicles in the United States and abroad.  Since its inception in 1990, the project has built 12 cars and has raced numerous times in the American Solar Challenge and the World Solar Challenge.  The project's teams have placed either first or second 15 times.  For more information about the University of Minnesota Solar Vehicle Project, visit, e-mail or call 612-460-7876.

About Jet Edge, Inc.

Established in 1984, Jet Edge is a global designer and manufacturer of waterjet systems for precision cutting, surface preparation and coating removal. Jet Edge waterjets are used around the world in a broad range of industries, from the world's leading airlines to automotive, aerospace, industrial manufacturers, machine and job shops. Jet Edge waterjet systems are proudly made in the U.S.A.  For more information about Jet Edge, visit, e-mail or call 1-800-JET-EDGE (538-3343). Follow us on Twitter @jetedge.

Jet Edge, Inc. | 12070 43rd Street N.E. | St. Michael, MN  55376-8427 U.S.A. | 800-JET-EDGE |


Nancy Lauseng  

Marketing Manager      

763-497-8726 |

Jaimie Larson

Sales Marketing Assistant

763-497-8742 |

More from Packaging Products & Equipment

All Topics