Texas Instruments
Dallas, TX 75243
Share:
Clock Multiplier offers hot-programmable operation.
Capable of in-system spread spectrum adjustment, CDCE906 lets designers hot-program its 3 PLL components in-circuit to generate 6 output clocks from single source for any frequency up to 167 MHz. PLL dividers provide low-jitter clock from 27 MHz crystal clock and feature zero ppm output clock error for most A/V frequencies. Along with 60 psec jitter, product offers programmable output slew-rate...
Read More »Battery Charge IC suits multi-cell portable electronics.
Interfacing to system's host controller through SMBus communications interface, Model bq24721 offers 0.4% accuracy on charge voltage regulation and 2% accuracy on current amplifier outputs. Using synchronous NMOS-NMOS rectifier, device can achieve power efficiencies up to 94%. Power selector function automatically selects ac adaptor or battery to properly manage system load. Dynamic power...
Read More »Video Switches suit DVI or HDMI applications.
Providing signal conditioning and switching, 3-port Model TMDS341 supports 4 TMDS channels, 1 hot plug detector, and I2C interface on each port. Each Transition Minimized Differential Signaling channel allows signaling rates up to 1.65 Gbps. Five-channel, 2:1 multiplexer/demultiplexer Model TS3DV520 converts 1 DVI or HDMI input port into 2 high-speed ports. Bandwidth of 2.4 Gbps allows each...
Read More »Transceivers allow up to 256 devices on single RS-485 bus.
Offering ESD protection in excess of 15kV, Models SN65HVD33/34/35 and SN65HVD53/54/55 are comprised of differential line drivers and receivers, with separate input and output pins for full-duplex bus communication designs. Units feature slew-rated controlled outputs to avoid unwanted reflections, and accurate data transmission for signaling rates of 1, 5, and 25 Mbps. Power supply options include...
Read More »Amplifier is suited for DAQ, control, and test equipment.
Manufactured in MSOP8 package, INA159 level-shifting difference amplifier has gain of 0.2 and is designed to interface -
Read More »Low-Latency, 16-Channel ADC provides fully settled data.
Manufactured in 7 x 7 mm QFN-48 package, ADS1258 is fabricated on precision mixed-signal CMOS technology and optimized for multi-channel applications. This 24-bit ADC offers fixed-channel (125 kS/sec data rate) or automatic channel scan (23.7 kS/sec data rate) modes with 20 bits of effective resolution. Along with low latency (42 -µs), product features externally accessible output,...
Read More »RF Synthesizer suits wireless infrastructure applications.
Able to maintain signal integrity for wireless infrastructure applications, TRF3761 eliminates need to integrate PLL devices with VCOs, buffers, and passive circuitry modules by integrating their equivalent functionality into 6 x 6 mm chip. It supports 3G wireless standards, as well as 2G and 2.5G, and is available at extended frequency range of 400 MHz to 2.5 GHz. At 1.9 GHz output frequency,...
Read More »Clock Multiplier provides jitter less than 60 psec.
Supplied in 20-pin TSSOP, CDCE706 integrates 3 on-chip PLL components that can accept crystal, LVCMOS, or differential input and generate 6 clocks from one clock source. Its 6 outputs can be programmed in-circuit or during operation for clock frequencies up to 300 MHz, minimizing EMI. Product integrates on-chip EEPROM technology, 2-wire SMBus interface, and programmable spread spectrum clocking....
Read More »Operational Amplifier drives wide variety of loads.
Operating from single or dual supplies, Model OPA567 has rail-to-rail swing on input and output. Output swing is within 300 mV of supply rails with output current of 2 A. Diagnostic flag is provided for temperature overstress and can be configured to provide thermal shutdown. Housed in 5 x 5 mm QFN package, op amp is suited for driving valves, actuators, laser diode pumps, and servo motors, as...
Read More »Microcontrollers target battery-powered applications.
Utilizing very low-power oscillator technology, Series MSP430F20xx delivers 500 nanoamp standby mode and is totally self-clocked with self-wakeup capability using no external components. Digitally controlled oscillator is programmable up to 16 MHz with ability to switch from standby to full operation in less than 1 -µs. Operating from 1.8-3.6 V, microcontrollers enable fire detectors and...
Read More »