Glenro, Inc.
Paterson, NJ 07501 1799
Oct 29, 2009 Cantilevered Multi-Unwind and Rewind System offers auto edge control that is accurate to ±1 mm, and auto jog that allows material to automatically advance when pulled over load cell roll. System's auto run mode automatically unwinds start tension control when tension set point is reached. Configurable, PID-controlled product allows enable/disable, under/over-wind, tapering, and side-lay of each winder. It is suited for webs up to 18 in. wide with 20 in. roll dia and 100 lb roll weight.

R.G. Egan Equipment, Inc.
Webster, NY 14580
Jul 02, 2009 Engineered to be automatic roll cleaning system, CI Drum Cleaner is designed for companies printing wide web packaging material and manufacturers of central impression (CI) printing presses. It performs thorough wiping of drum to remove ink, dirt, and slip from its surface. Able to retrofit to most manufacturers' CI printing presses, solution allows for full 24 hr of printing without needing to stop press for manual drum cleaning.

Radio Frequency Co., Inc.
Millis, MA 02054
Jun 09, 2009 Macrowave(TM) RF Drying System selectively heats coated portions on web leaving bound moisture in substrate intact, preventing overdrying, distortion, and shrinking. It operates at up to 1,500 fpm, with RF power being instant on/off and energy only consumed in proportion to load in system. Configurable to handle webs up to 120 in. wide, RF drying system meets OSHA safety regulations and FCC standards on communication noninterference.

Davis-Standard, LLC
Pawcatuck, CT 06379
Mar 24, 2009 Black Clawson machinery is available with multiple pelletizing features, such as air ring pelletizing system that enables cutting of materials that should not come into contact with water quench media or those with low heat removal requirement. Also, debottlenecking retrofits are available to increase production capacity utilizing X model version. Pelletizer die plate design promotes throughput rate proportional to die plate orifice holes.

Abbeon California, Inc.
Santa Barbara, CA 93101
Jan 19, 2009 With transformer replaced by high-tech electronics, AZTC-20 electronic thermocutter cuts synthetic fabrics, plastic tubes, fiber optics, foam and similar materials that tend to crimp, serrate or unravel when cold cutters are used. Temperature in unit is controlled from zero to 1050ºF, while electrical current control switch allows selection of large blades. Cutting foot accessory lifts synthetic fabric or thin plastic off cutting surface before coming in contact with heated blade.

Brother International Corp.
Bridgewater, NJ 08807
Jan 05, 2009 Featuring independently controlled dual platen and dual print-head modules, Model GT-782 is capable of printing 2 different designs on separate platens simultaneously. White ink and ink cartridge system promote optimal output quality and 4 industrial-grade print-heads provide optimal printing speed for white ink applications. Along with print area of 16 x 18 in., system features print driver software that can directly interface most graphic applications.

The Eraser Company, Inc.
Syracuse, NY 13221
Nov 20, 2008 Microprocessor-controlled MMC200 cuts round or flat material up to 3.94 in. wide and 5/8 in. thick and can be programmed to cut any length (in. or mm), with 1% or better tolerance. It is also programmable for up to 99 batches and 10 fixed feed rates. MMC200 is rated to cut up to 7,592, 2-in. pieces/hr through makerials such as copper wire and cable, silver solder, power cords, cellophane, fiberglass sleeving, latex, fabrics, belting, flat and ribbon cable, strapping, hosing and tubing.

Gerber Technology, Inc.
Tolland, CT 06084
Aug 07, 2008 Supplied with CutWorks® software for full automation, single-ply GERBERcutter® Models DCS3600/3600L include TargetVision digital camera technology for capturing detailed images of materials placed on cutting table. AutoMat System, which addresses requirements of specialized mat industry, uses scanner technology that recognizes where mat's carpet and rubber border meet. With longer cut window, Model DCS3600L enables manufacturers to cut pieces up to 10 ft in length between bites.

Spartanics
Rolling Meadows, IL 60008
Jul 02, 2008 Featuring flat or vertical design, Sheet and Web Contact Drying System thoroughly dries wet inks from material surface to top side, avoiding residual moisture problems. System uses heated vacuum plate with transport belt on bottom of material being dried. Integrated heated air blower furthers drying process and helps eliminate solvent fumes. With system, screen printed materials that previously required 2 hours to dry can be dried within 30 seconds.

Radio Frequency Co., Inc.
Millis, MA 02054
Jul 01, 2008 Designed for high-speed drying of water-based patterned glue and coatings, Macrowave(TM) RF Drying System selectively heats only patterned coatings on web and leaves bound moisture in substrate intact, preventing over-drying, distortion, and shrinking. It needs 1/3 to 1/5 of floor space required for hot air and IR dryers, and permits lower web temperatures. Unit can handle webs up to 120° wide and meets OSHA safety regulations and FCC standards on communication non-interference.

MEGTEC Systems
De Pere, WI 54115-5030
Jul 01, 2008 Developed for 80-page presses with web width up to 2,400 mm, DLC 6000 Match-Speed Splicer can handle 60 in. diameter rolls at max production speed of 3,540 fpm. Rolls load into paster by automatic roll-handling systems that have adjustable automation level, allowing roll changing without operator. Additional features include split-arms that minimize changeover time when changing web width, integrated infeed unit with 290 daN max web tension, and quick-change 3 and 6 in. chucks.

MEGTEC Systems
De Pere, WI 54115-5030
Jul 01, 2008 With splice efficiency rating over 99.5%, MP Series carries newspaper rolls from 40-67 in. wide with roll diameter of 50 in. Rolls can be loaded manually or automatically direct from floor level. Fully automatic chucks are positively locked into core and do not have to be re-tightened during running. Adjustable up to 67 in., split arm permits loading of 2 rolls with different widths. Single and double width models are available with 2- or 4-quadrant drive capability.

MEGTEC Systems
De Pere, WI 54115-5030
Jun 30, 2008 Roll-Blade RQS incorporates optimized web-air-transport system, Airstream II, which optimizes performance levels while minimizing energy consumption and noise. Available with speeds to 50,000 and 60,000 cp/h, sheeter enables important process parameters to be adjusted centrally during production. Papers of different quality can be used without problems, and Web Snap system avoids paper wraps at low paper weights.

Gerber Scientific Products, Inc.
South Windsor, CT 06074
Jun 24, 2008 With programmable machine settings, GERBERcutter® Z7 multi-ply cutter helps maximize throughput and yield while cutting intricate shapes, multiple hole sizes, and notches. It is suited for full range of material types and thicknesses, including bi-laminate foams, technical textiles, and high-loft fabrics. Product targets automotive, aerospace, and technical textiles markets.

PermaFlex Engineering
Orange, MA 01364
Mar 18, 2008 Configured vertically or horizontally, AccuNip® Nip Stations with aluminum frames offer nip loads up to 2,000 lb, while cast iron and steel frame units produce up to 25,000 lb of nip load. Stations can be customized with doctor blades, dual-roll gear drives, heating or cooling rolls, and adjustable nip pressures and gaps. Light- and medium-duty models are suited for laminating, thermal bonding, web heating/cooling, and web pulling or squeezing.

Gerber Technology, Inc.
Tolland, CT 06084
Aug 01, 2007 GERBERspreader XLs125 ensures material rolls weighing up to 160 lb are spread without tension and that edges are perfectly aligned. Capable of spreading woven or knit materials in roll or flat form for variety of applications, machine enables parts to be nested closer to beginning, end, and edges of spread. Windows®-based, icon-driven interface facilitates operation, while fabric roll cradle feed system tilts automatically to facilitate loading and unloading.

Nim-Cor, Inc.
Nashua, NH 03061
Jul 30, 2007 Targeting web-process industry, Roll Restorer utilizes hydraulic pressure to reform damaged cores from 2-12 in. ID. Mobile cart provides storage and mobility while carrying all expander heads and flanges for different core sizes. With Roll Restorer, operators can salvage good product and avoid lost productivity when damaged cores prevent conventional unwind mounting.

Andantex USA, Inc.
Wanamasa, NJ 07712
Apr 24, 2007 Digital controller, Merobel DGT300, provides regulation capabilities for printing, labeling, and converting machinery. Employing Windows-based software, unit contains programming options such as inertia compensation, taper adjustment, on-the-fly management of web turrets, and E-stop torque control in proportion to set point. Solution, operable in closed- as well as open-loop modes, contains 5 built-in memories and one integral power supply.

Breach Security, Inc.
Carlsbad, CA 92011
Dec 01, 2006 Incorporating ModSecurity(TM) v2.0 open source web application firewall, ModSecurity Pro(TM) M1000 appliance includes rule sets for compliance with Payment Card Industry v1.1, as well as protection for Microsoft(TM) Outlook Web Access (OWA). Hardened appliance is built with secure configurations of OS and Apache web server, and uses SSL encryption module to provide network encryption. It also has capability to run antivirus applications to scan uploaded files.

Double E Co., Inc.
West Bridgewater, MA 02379
Nov 07, 2006 Featuring wear-resistant gripping elements and polyethylene centering strips, SRS-2000 self-centering strip shaft creates and maintains consistent axis of rotation for roll. Centering strips support roll as bladders compress during rotation, minimizing roll bounce, and independent bladder control system. Available in 3 and 6 in. diameters, shaft utilizes air activation system with no moving parts.