Scientific & Engineering

Software, Controls & Controllers

Process Control System works with bioreactors and mixers.

January 12, 2016

Powered by DeltaV® Controller from Emerson Process Management, TruBio® DV v5.0 can be used with glass vessels, rockers, media or buffer mixers, and most single-use bioreactors to provide seamless solution from 0.5 L R&D through 2000 L cGMP-compliant production. Software leverages SmartParts™ intelligent digital actuators to implement off-the-shelf solutions for continuous processing and automated harvest. It offers multi-feed dosing and can create batch recipes for mixing and buffer preparation. Read More

Software, Laboratory and Research Supplies & Equipment

Automated Module aids spectroscopic collection, model development.

January 8, 2016

EDX Experiment Design and Execution Module automates spectroscopic data collection and chemometric model development. Without requiring duplicate manual data entry, functionality allows spectra to be collected using Symbion LX, DX, or RX and transferred directly to Symbion QT chemometrics. During collection, user can add variables, create component values spreadsheet, and annotate memo block for each spectrum. Users can also, upon deployment, add multiple trends based on calculations. Read More

Test & Measuring Instruments, Software

Oscilloscopes test DisplayPort 1.3 compliance.

December 15, 2015

With U7232D DisplayPort 1.3 compliance and validation test software, Infiniium Oscilloscopes can perform physical-layer tests required for DisplayPort 1.3 source devices. Software guides users sequentially through tasks, executes tests, and conveys test information through software-generated report. Program features support for multiple standards, physical-layer AUX channel tests, test automation support, and measurement parameter configurability for debugging. Read More

Software

Pipe Stress Analysis Software supports recent code standards.

November 9, 2015

CAESAR II® 2016 evaluates structural responses and stresses of piping systems to international codes and standards. By leveraging FEATools™ from Paulin Research Group, program can add finite element analysis capabilities to CAESAR II jobs, including more accurate stress intensification factors and flexibility factors in analysis. Software also provides optimized distance measurement, faster piping data input, and redesigned Static Analysis Load Case Editor. Read More

Software

Automation Development Software offers all-in-one functionality.

November 5, 2015

Helping users leverage multiple fieldbus compatibility, modular design, and processing speed of PFC200, e!COCKPIT software development environment supports every automation task – hardware configuration, programming, networking, simulation, and visualization – in one package. This seamless and synchronized platform includes such features as built-in HTML 5 visualization tool and software libraries, embedded  CODESYS v3, and programming based on standard IEC 61131 languages. Read More

Software

3D Design Software streamlines PCB development.

October 22, 2015

Minimizing iterations with mechanical and manufacturing teams, PADS® uses 3D engine that enables full 3D visualization, placement, and design rule checking. Schematic design and layout abilities foster usability across flow, and commercial engine supports large databases. Along with optional 4 million parts 3D library and ECAD-MCAD collaboration tool, features include reference designator placement with physical design reuse elements, padstack editing, and translator/migration tools. Read More

Software

Structural Design Software automates building analysis.

October 9, 2015

With Tekla® Structural Designer, engineers can analyze and design steel and concrete buildings by combining analysis and design into single, seamless process. Program offers expanded beam design options as well as expanded seismic analysis and design features that automate accidental torsional effects and required seismic design combinations. Other time saving features include automation of tedious and complex tasks such as wind loading calculations, floor vibration checks, and floor loading. Read More

Software

FPGA Design Software optimizes power consumption and more.

October 6, 2015

Used for development of FPGA products, Libero system-on-chip (SoC) v11.6 supports RTG4™ high-speed signal processing radiation-tolerant FPGAs and enhances usability for DDR and high-speed serial designs. RTG4 support includes IO Advisor, SmartPower, and uProm support, and additional features are available for SmartFusion™2 SoC FPGAs and IGLOO™2 FPGAs. Solution automatically optimizes hold violations using minimum delay repair and provides multi-pass options in layout for large designs. Read More

Software

Engineering Software handles complex simulations.

August 13, 2015

ANSYS® v16.2 lets engineers create virtual prototypes of complete systems. Performance is bolstered by integrating functionality of ANSYS Simplorer® multidisciplinary systems modeling platform, ANSYS AIM® integrated multiphysics simulation environment, ANSYS Customization Toolkit (ACT), and ANSYS SCADE System Avionics Package™. Latter addresses critical workflow and automation for complex systems engineering by automating development of embedded software systems for avionics. Read More

Test & Measuring Instruments, Software

CAE Software offers vibration, frequency domain testing.

April 28, 2015

With capabilities for vibration fatigue and frequency analysis, nCode v11.0 helps engineers avoid unnecessary over-design and prevent operational failures. Modal Superposition support increases allowable model size, number of frequency steps, frequency range, fidelity of results, and analysis speed. Along with vibration fatigue solver, features include strain gauge analysis engine, complete fatigue solution, and frequency analysis with pre-defined processes. Read More

Software

Boundary Scan Software helps access full JTAG capabilities.

April 23, 2015

Offering dynamic chain profiling, XJTAG v3.3 helps initialize boards with multiple JTAG chains, in which device in one JTAG chain controls power supplies or reset lines for JTAG devices in other chains. During flash programming, it is possible to set up XJTAG to only clock JTAG data through chain that is needed for programming operation, leaving other chain(s) held in current state. In addition, user can describe connections from XJLink2 controller to PCB under test. Read More

Software

Compliance Test Benches foster PCI Express, USB insights.

April 17, 2015

Providing complete workflow, Advanced Design System PCIe and USB Compliance Test Benches enable SerDes engineers to use simulation to ensure candidate design yields fabricated prototype compliant to specifications of PCI Special Interest Group and USB Implementers Forum, respectively. Products provide customizable test harness in which to simulate IP as well as post-processing scripting capability (Waveform Bridge) that exports simulated waveforms to compliance application. Read More

Software

Engineering Software targets plant and marine projects.

April 17, 2015

AVEVA Electrical and AVEVA Instrumentation are Citrix Ready applications intended for electrical and instrumentation engineering and design in plant and marine projects. Functionality allows accurate cable length and sizing calculations and also includes cable routing capabilities based on AVEVA Everything3D (AVEVA E3D). Capabilities enable flexible project configuration/control for distributed engineering teams.
Read More

Software

CAD Software offers reverse engineering options.

April 17, 2015

Combining solid, surface, and direct modeling with reverse engineering, PowerSHAPE Pro 2015 R2 minimizes need to transfer data between multiple programs. Software includes split-screen alignment option and can connect directly to most scanning hardware to capture and display scan data in real-time. Able to morph complete solid or surface model to mesh, PowerSHAPE Pro can use Smart Feature Selector to display type and parameters of each feature interactively as cursor is moved around model. Read More

Software

Signal Generation Software suits aerospace/defense industry.

April 10, 2015

Used for multi-emitter scenario generation, N7660B Signal Studio enables aerospace/defense engineers to download performance-optimized multi-emitter signals to one or more Keysight N5193A UXG agile signal generators for effective testing of electronic countermeasures systems. Program simplifies threat interleaving for ECM system test applications such as sorting and identification, subsystem interface management, and threat correlation. Read More

Software

Lab Resource Management Software increases procedural efficiency.

April 10, 2015

By optimizing resource utilization, QATrax test laboratory management software helps increase efficiency for lab users. Solution delivers Web-based test status covering resource usage and other important metrics, which can be referred to by engineers and managers. Others can also see data when allowed. Tuning testing cycles to business cycles, software simplifies resource scheduling of tests, equipment, and technicians. Read More

Software

Automotive Lighting Design Software offers photorealistic images.

April 8, 2015

LucidShape® v2.0 helps accelerate design development, verification, and delivery for automotive lighting engineers. By depicting all interactions between system geometry and light sources, included Visualize Module delivers high-speed photorealistic images of automotive lighting system's lit appearance. Other features include Ray Data Viewer that creates ray data source-based illuminance images, Light Pipe Tool, and measured Bidirectional Scatter Distribution Function surface material library. Read More

Software

Automated Test Software supports multiport DUTs.

April 7, 2015

Designed to boost speed and efficiency, R&S ZNrun Software assists users in configuring measurements specifically for multiport DUTs using R&S vector network analyzers. User selects VNA and any additional test equipment and sets parameters to be measured on DUT. Based on this information, software takes over communications with test equipment, makes all settings, and executes and controls test sequence. Procedure simplifies time-consuming characterization of multiport components. Read More

Software, Services

PHY Test Suite simplifies USB3.1 compliance testing.

April 2, 2015

Providing automated transmitter and receiver compliance testing, characterization, and debug, QPHY-USB3.1-Tx-Rx Software can perform tests on both 5 Gbps Gen1 and 10 Gbps Gen2 devices according to USB 3.1 specifications. Tx testing is performed using 16 GHz oscilloscope, while Rx testing is performed using PeRT(3) Protocol Enabled Receiver and Transmitter Tolerance Tester. QualiPHY automated test framework provides connection diagrams, automated oscilloscope operation, and report generation. Read More

Sensors, Monitors & Transducers, Software

Test Application verifies loudspeaker performance to TTA standard.

April 2, 2015

Using API of APx audio test software to control and interact with APx500 Series audio analyzer, APx TTA Loudspeaker Test Utility verifies performance of micro and slim speakers to TTA standard TCB-0054(00) – TTA Verified Testing Criteria for Micro/Slim Speakers. Tests performed include Effective Frequency Range, Distortion and Sensitivity, Maximum Sound Pressure Level, and Impedance. Requirements include software option SPK-RD, IMP1 Impedance Fixture, PA, and measurement microphone. Read More