Bridgeport’s Zinc Alloy Fittings Listed for Use with Aluminum EMT Means Contractors Can Install an EMT System that Won’t RustApril 21, 2017
STRATFORD, Conn. (April 19, 2017) – Electricians have often asked, “Why doesn’t an EMT manufacturer make corrosion-resistant tubing that won’t rust.” Now with aluminum EMT, contractors have their wish and can put away their rigid conduit threaders and reamers.
Aluminum EMT is the perfect material choice for indoor or outdoor, damp, wet or exposed environments. With... Read More
Made of one-piece rubber body and pressure-relieving system integrated into glass-filled nylon core, Test-Tite® Pneumatic Test Plug are available in 1-1/2 in. , 2 in., 3 in. and 4 in. sizes in 6 and 12 pack case configurations. Units are designed is such a way that excess air is relieved into atmosphere before the deformation of plug.Read More
Molded from RADEL® resin F1960 Poly Pex Cold Expansion Fittings are available in couplings, elbows, male adapters, tees and rings with stops configurations in different sizes. Featuring 320ºF of maximum temperature rating and maximum operating temperature of 210ºF at 150 PSI, fittings meet NSF 14/NSF/ANSI 372/NSF/ANSI 61 and CS B137.5 standards.Read More
Available in ½ - 1 in. sizes, UNF and UNY Fittings are made of Type 316 SS. Fittings are used for joining threaded lengths of conduit or to connect rigid conduit to devices, boxes or enclosures.Read More
MINNEAPOLIS, Minn. - March 29, 2017 - More than 1,000 operational satellites currently in orbit will one day run out of fuel and burn up in our atmosphere as they fall back towards Earth or remain space debris forever.
Costing tens of millions of dollars each launch, satellites have a limited lifespan restricted by their fuel tank capacity. However, with NASA's continued research,... Read More
Bridgeport Solution Enables Midwest Contractor to Meet Demanding Chedule in Completion of Large-Scale Building RenovationMarch 24, 2017
Electrical contractor takes advantage of Bridgeport’s new Mighty-Merge® multi-port transition couplings for major project
STRATFORD, Conn. (March 20, 2017) – If timing is everything, then for a Midwest electrical contractor the timing could not have been better. The contractor was awarded a fast-paced rewiring job of a major automotive design facility and office building just after... Read More
There is a large variety of pipe plugging and blocking requirements throughout a wide range of industries, including repair work, leak testing, weld purging and debris stopping. One major concern is the entry of debris into pipes during operations.
COB Industries supply a range of low cost, lightweight Inflatable Stoppers, available for pipes up to 120” diameter to prevent the entry... Read More
CINCINNATI, OH (March 6, 2017) – Hollaender® Manufacturing, manufacturer of Speed-Rail®brand solar pipe rack fittings, has received UL 2703 Recognized Component Approval under Intertek ETL mark No. 5006508. UL 2703 is solar industry standard covering rack mounting systems, mounting grounding/bonding components, and clamping/retention devices for specific flat-plate photovoltaic modules and... Read More
TORONTO and NEW YORK, March 03, 2017 - Micromem Technologies Inc. (“Micromem”) (“the Company”) (CSE:MRM) (OTCQX:MMTIF) through its wholly owned subsidiary Micromem Applied Sensor Technologies Inc. (MAST), announces it has received the 5th of 6 patents filed for the oil pan plug. Receipt of the 6th patent is expected by mid-June. This will complete the patents filed and give the Company... Read More
Used with aluminum or galvanized steel, Speed-Rail Slip-on Pipe Fittings are strong and lightweight, having fixed and adjustable configurations. Pipe Rack Fittings are available in 25R-9 replacing rear cap, 17 adjustable tee replacing slider, 25S-9 replacing front cap, and 5-9 replaces front cap when no bracing is required. All Speed-Rail fittings are made of corrosion resistant 535.0... Read More
Used in ceiling installation for communications and power, hard-to-reach 90-degree bends under decks and below floors, ICE Inside Corner Elbow allows for multiple conduit runs which are to be installed in parallel without interference while accessing elbow’s cover. Providing smooth pulling surface for conductors to glide against, product enables for easy access when adding or removing cables... Read More
Featuring superior-quality compression seal, HelaGuard Conduit and Fittings are suitable for maximizing product reliability in manufacturing, machine building, shipping and chemical industries. Designed with galvanized, jacketed, liquid-tight metal core conduit for flexibility and crush resistance, units protect electrical wires from mechanical failure caused by vibration, impact and moisture... Read More
Available in NSF approved materials with NSF-51® and NSF-61® certifications, HydroMode™ push-to-connect fittings can be used with polyethylene and other flexible tubing. Having up to 145psi at 70°C pressure and Shore A 98 hardness rating, product comes in 5/32 in. to 1/2 in. sizes and black, blue, natural, red, yellow, green, and white colors. Unit's body and collet of fittings are... Read More
Designed for heating and passing DEF throughout SCR system on commercial vehicles, SCR Hoses use nylon core tubes for on-vehicle DEF transfer. Eliminating problems of condensation, coagulation and freezing of liquids inside hose, unit uses extruded sheath to lock-in heating elements and provides uniform heating for longer time. Hoses are available in 4mm and 5.5mm EPDM cores and 6mm nylon core... Read More
We have been the exclusive manufacturer for Dimple Magnetic Motor Oil Plugs for 6 years. We have been involved with new designs and applications to constantly improve this product line. www.drainplugsmagnets.com
Hawk Manufacturing, Inc.
220 Zimmer Rd.
Indian Land, SC 29707
Replacement Fittings for Most Foreign Manufactured Equipment
Mentor, OH, December 27, 2016 – Malone Specialty Inc., a quality manufacturer of industrial hose and hose fittings for over 30 years, is now manufacturing and stocking standard Metric Flat Face Fittings.
Steve Malone, President of Malone Specialty Inc. stated, “For years we have been providing metric fittings and... Read More
Ideal for industrial, commercial and residential applications, MegaPress and MegaPressG P x P reducers and P x FPT union fittings are available in 1/2", 3/4", 1", 1 1/4", 1 1/2" and 2" sizes. The fittings use stainless steel with EPDM sealing element for MegaPress system and HNBR stainless steel separator ring for MegaPressG system to ensure sealing element and grip ring maximum... Read More
Bridgeport’s “Team Done That” saves the day for large Texas contractor faced with delay in finding right fitting for construction projectNovember 30, 2016
STRATFORD, Conn. (Nov. 28, 2016) - While constructing a multi-story parking deck, a large contractor in Texas was having difficulty finding and installing a properly sized fitting listed for concrete encasement of Jacketed MC-PCS cable. The fitting the contractor was using was damaging the conductors during installation. That’s when a member of Bridgeport’s ‘Team Done That’ sprang... Read More
Pipe plugs and stoppers are in use globally for a large variety of applications. This includes leak testing, weld purging, debris stopping and pipe freezing for repair or maintenance work for thousands of different industries.
Manufacturing a wide range of plugs and stoppers of up to two meters in diameter, Huntingdon Fusion Techniques HFT®’s Pipestoppers® Division will ensure that... Read More
Featuring multilobed seal for redundant protection against leakage, LQ2 Series Quick Disconnect Coupling offers lasting shape retention during extended periods of connection. With reduced pressure drops of average 34 percent, device optimizes liquid cooling system performance. Providing highest-flow capacity 1/8-inch connectors in the liquid cooling industry, couplings allow one-handed... Read More