Company News

NuSil Technology LLC

1140 Mark Ave., Carpinteria, CA, 93013, US

  • 805-684-8780

Public Relations:
Kristen McCarthy
Public Relations Specialist
The Phelps Group
901 Wilshire Blvd
Santa Monica, CA 90401 USA
E-mail this person

Share Like Tweet Add Email

Latest New Product News from
NuSil Technology

Adhesives & Sealants, Chemical Processing & Waste Management, Materials & Material Processing

Electronic Packaging Material is thermally conductive.

August 23, 2012

With nominal thermal conductivity of 1 W/mk, EPM1-2493 silicone thermal interface material offers bond lines as thin as 5 microns and is suited for use in electronic applications. This pourable, conformal liquid, with 1:1 mix ratio, can be used to adhere materials with differing coefficients of thermal expansion (CTE), reducing stress during thermal cycling. Adhesive strength can be improved via use of primer, achieving average lap shear values of 120 psi. Read More

Materials & Material Processing, Optics & Photonics, Adhesives & Sealants

High-Purity Gels exhibit minimal moisture permeability.

June 10, 2009

Available with refractive index of 1.54 and viscosities from 3,500-8,000 cP, LS-3354, LS2-3354, and LS3-3354 are designed for potting, encapsulating, backfilling, and dampening applications requiring soft gel with optical clarity. Cure can be achieved at ambient temperatures with humidity or accelerated with heat, and gels can be removed for rework if needed. Available in 1:1 mix ratio, products are suited for protecting electronic components from dust, debris, and moisture. Read More

Chemical Processing & Waste Management, Adhesives & Sealants, Materials & Material Processing

Silicone Gel offers refractive index of 1.40.

June 4, 2009

Providing protection from mechanical shock, optically clear LS-3140 is suited for use as encapsulating, embedding, or potting compound for environmental protection of electronic assemblies. Low outgassing gel handles stress during thermal cycling without cracking or delamination. To meet multitude of processing requirements, LS-3140 cures at room temperature, or cure can be accelerated with heat. It is best suited for applications requiring operating temperature of -94 to 392°F. Read More

Chemical Processing & Waste Management, Materials & Material Processing

Aerospace Material suits solvent-resistant applications.

September 30, 2008

Fluorosilicone high consistency rubber (HCR), FS-3780, is designed to endure harsh environments where finished parts are exposed to fuels and extreme temperature conditions. Delivered as uncatalyzed HCR, it requires addition of platinum- or peroxide-base catalyst to cure with heat. It can be used for transfer or compression molded parts - gaskets, stoppers, seals - and can also be extruded or calendared depending on processing requirements. Read More

Materials & Material Processing, Chemical Processing & Waste Management

Dielectric Gels suit electronic packaging applications.

February 27, 2007

Low-outgassing EPM-2480, EPM-2481, and EPM-2482 are designed for encapsulation of chip packages in devices where outgassing-related contamination would be problematic. Able to cure into soft, compliant silicone, products help reduce stress on electronic assemblies during temperature cycling while protecting against environmental factors and shock. Types EPM-2480 and EPM-2481 are based on dimethyl silicone systems, while EPM-2482 is based on diphenyl dimethyl silicone system. Read More

Packaging Equipment, Chemical Processing & Waste Management, Adhesives & Sealants

Silicone Material suits electronic packaging applications.

November 14, 2006

Low outgassing, one-part material EPM-2411-2 glop-top is designed for encapsulation of chip packages in devices where outgassing-related contamination poses problem. Product exhibits low stress and wide operating temperature ranges characteristically associated with silicone-based materials. It is stored and shipped frozen in 3 and 30 cc syringes as well as 3 and 6 oz tubes. Read More

Materials & Material Processing

Thermal Interface Material has low-viscosity formulation.

August 2, 2006

Developed to address contamination issues in dense electronic systems, EPM-2493 electronic packaging material (EPM) meets requirements of high-temperature and high-stress operating conditions in electronic packaging. This low-outgassing material is designed to work in environments with drastic temperature cycling that would otherwise result in encapsulant embrittling or outgassing. Read More

Materials & Material Processing

Two-Part Silicone Compound suits electronic applications.

March 12, 2003

Able to maintain electrical conductivity from -178 to +445°F, R-2634 electrically conductive, room-temperature vulcanized (RTV) paste achieves full cure at 77°F in 7 days. With heat-accelerated cure time of 30 min, R-2940 thermally conductive, RTV paste performs over -85 to +465°F temperature range. Operating over -178 to +465°F temperature range, CFI-6755 optically clear, RTV liquid elastomer achieves full cure (heat-accelerated) in 10 min. Read More

Other Company News from
NuSil Technology