Gating Inserts are fully countourable.
Inserts

Gating Inserts are fully countourable.

Designed for tunnel-type (submarine) gates, Z10650 gating inserts are provided with added stock, making them individually contourable, which allows direct adaptation to contours of mold. They leave no evidence of gate on upper side of molded part, and enable clean separation of sprue. Produced by MIM process and made of wear-resistant hot-work steel 1.3343, inserts are available in three sizes.

Read More »
Miscellaneous Film

Card Sleeves protect against theft of personal information.

Suited for smart cards, e-passports, ID cards, banking/credit cards, and transportation cards, 3M ToughShield Protective Sleeves block radio frequencies to help eleiminate data theft or skimming. Inner copper-coated conductive polyester layer is bonded to outside layer of 3M TufQUIN inorganic hybrid insulating paper. This material is tear- and water-resistant and also withstands wear. After 2,000...

Read More »
Stick Electrode offers 70,000 psi minimum tensile strength.
Welding Rods, Wire and Electrodes

Stick Electrode offers 70,000 psi minimum tensile strength.

Available in 1/8, 5/32, 3/16, 7/32, and -¼ in. dia, Rocket 7024 stick electrode features self-removing slag system that completely releases slag. Electrode is designed for DCEN, AC, or DCEP welding, and also suits general plate, tank and construction equipment fabrication, and SMAW applications. Offering smooth arc and low spatter levels, product meets AWS E7024 requirements for horizontal...

Read More »
Sleeves

Replace Diffuser Sleeves to Improve Performance

Aqua-Aerobic Systems, Inc. offers replacement diffuser sleeves for fine bubble diffusers for AquaSBR® systems or other activated sludge processes. This new program is designed to return the diffused air system back to peak operating efficiency. Reduced efficiency is often due to an aging system. Diffuser headloss increases and SOTE decreases due to hardening of the sleeves as plasticizers slowly...

Read More »
How to Maintain Joint Integrity When Converting from Metal to Plastic
Sponsored

How to Maintain Joint Integrity When Converting from Metal to Plastic

Discussing how the joint integrity of an assembly can be maintained while converting from metal inserts to plastic, this paper points that tensile strength, rotational torque, and pull-through strength are the typical performance requirements of an assembly. It lists the factors which affect the insert performance like insert type, design, plastic specifications, and installation process, and briefly details the different styles of inserts which are designed to accommodate various performance requirements and installation methods. Also explained in the paper is about the hole designing in different inserts, along with the figure illustrating the included taper angle in both straight hole and tapered hole. The paper concludes that in order to prevent jack-out affect in the assembly the hole in the mating component must be larger than the outside diameter of the assembly screw but smaller than the face diameter of the insert.

Read More »
Air / Gas Compressors

Air Generators eliminate gas cylinders from laboratory.

Available in 8 models, Balston® UHP Zero Grade Air Generators produce up to 280 lpm of hydrocarbon-free air from existing compressed air supply, allowing gas cylinder users to supply, control, and automate gas supplies. Zero air purity exceeds cylinder gas quality as hydrocarbon content is less than 0.05 ppm and is measured as methane. Units are suited for supplying air to LC mass spectrometers,...

Read More »
Stainless Steel Electrodes enable welding in all positions.
Welding Rods, Wire and Electrodes

Stainless Steel Electrodes enable welding in all positions.

Gas-shielded, flux cored, martensitic stainless steel electrodes are available in .045 and 1/16 in. dia. Select 410-AP contains 12% chromium, is utilized to weld straight 410 SS, and features corrosion and oxidation resistance up to 1,200°F. Used to weld ASTM CA6NM castings and certain 410, 410S, and 405 SS, Select 410NiMo-AP is composed of 12% chromium, 4.5% nickel, and .60% molybdenum with...

Read More »
Stainless Steel Electrodes suit corrosive environments.
Welding Rods, Wire and Electrodes

Stainless Steel Electrodes suit corrosive environments.

Bare wire and covered stainless steel electrodes, Arcos 317/317L, are developed for welding in corrosive environments where crevice and pitting corrosion are of concern. Arcos 317/317L (ER317/317L) bare wire features minimal carbon content, reducing possibility of intergranular carbide precipitation and increasing resistance to intergranular corrosion. Covered Arcos 317/317L electrode (E317/317L)...

Read More »
Flux-Cored Welding Wire targets X80 pipeline applications.
Welding Rods, Wire and Electrodes

Flux-Cored Welding Wire targets X80 pipeline applications.

Classified under AWS A5.29, class E81T8-Ni2 J, self-shielded Hobart® Fabshield X80 provides tensile strength of 94,000 psi, yield strength of 84,000 psi, and CVN impact values from 107 lb/ft at -20°F to 96 lb/ft at -40°F. Wire is available in 5/64 in. diameter and features fast-freezing slag that is nearly self-peeling, making it suited for welding in all positions. Product can be used for...

Read More »
TIG Welder handles steel, stainless steel, and aluminum.
Welders

TIG Welder handles steel, stainless steel, and aluminum.

Diversion 165 AC/DC TIG welder can weld 22 ga to 3/16 in. material in single pass and offers infinitely adjustable 10-165 A. Unit connects to 230 V, 1-phase power using dryer-type 3-pronged plug and requires 25 A circuit breaker. Designed for first-time welders that want to take on motorsports TIG applications, 50 lb system has controls for heat input and for selecting metal type. It produces...

Read More »
Contact Inserts reduce wiring and keying time.
Inserts

Contact Inserts reduce wiring and keying time.

Designed for Heavycon Series plug connectors, series B Push-In Contact Inserts allow flexible wires with ferrules or rigid wires to be connected directly without tools. Contact can be keyed by inserting plastic pins into contact coding slot. All fastening and connection screws are made of non-corrosive stainless steel. Inserts are available in 6, 10, 16, and 24 positions for 500 V or 16 A with...

Read More »
Basalt America Announces Stronger, Lighter, and Corrosion-Free FRP's (Fiber Reinforced Polymers)
Sponsored

Basalt America Announces Stronger, Lighter, and Corrosion-Free FRP's (Fiber Reinforced Polymers)

Fiber Reinforced Polymers (FRP), represents a truly groundbreaking advancement in structural reinforcement. Lightweight, strong, and green, they are changing the way the construction industry thinks about rebar. Unlike steel, FRPs don't rust and are far stronger than standard rebar. To learn why Fiber Reinforced Polymers are poised to change the way the world builds, see our video.

Read More »

All Topics