Sanitary Tank Washers meet USDA, FDA, and 3A standards.
Miscellaneous Washing Equipment

Sanitary Tank Washers meet USDA, FDA, and 3A standards.

Clipdisc clean-in-place (CIP) tank washers offer hygienic design that delivers cleaning action in 360° wash pattern at flow rates from 22 to 67 gpm. They completely remove cheese, whey, and other byproducts from deep and enclosed make vats, finishing vats, and conveyors after manufacturing. Clipdiscs operate at pressures from 20 to 60 psi. Cleaning radii range is 6.5 to 7.5 ft, and wetting...

Read More »
Parts Cleaner Exhaust System reduces moisture loss.
Parts Washing Equipment

Parts Cleaner Exhaust System reduces moisture loss.

Exhaust Moisture Reduction System for parts cleaning systems minimizes moisture escape, enhances part drying, and conserves water, chemistry, and energy. It works with aqueous based parts washing systems that rely on spraying heated water. Exhaust system pre-warms incoming make-up water and blow-off air, and directs exhaust moisture back to solution tank. Exhaust air can be vented directly to...

Read More »
Radiator Washer reduces reject rate.
Parts Washing Equipment

Radiator Washer reduces reject rate.

High-volume radiator washer has high velocity blow-off units that reduce cross contamination between process stages, and remove excess water from radiator's inherent dense coil to ensure complete drying capability. Full width interlocking access doors to spray wash stages facilitate maintenance. It has polished stainless steel construction, and natural gas heat for wash, rinse, and dry stages.

Read More »
Belt Washer System is suitable for high-production cleaning.
Washing Equipment

Belt Washer System is suitable for high-production cleaning.

Manual or automatic belt washer system is available in single or multi-stage configurations. System accommodates various part sizes and geometries using open weave conveyor belts or custom designed fixtures. Construction includes stainless steel tanks and enclosures and 1 x 1 in. stainless steel flat wire belts. Belt washer system is available with chip removal and electric, gas, or steam heating...

Read More »
Microplate Washer offers automatic bottom well detection.
Miscellaneous Washing Equipment

Microplate Washer offers automatic bottom well detection.

MW 96 automated programmable microplate washer is for use with strips and 96-well plates. It features pressure- and vacuum-free pump system for quiet operation. Washer can be configured with up to 3 different wash liquids and will store 50 wash procedures. Intuitive software facilitates programming of wide variety of wash cycles and procedures. Dispensing volumes and speeds, aspiration speeds and...

Read More »
Loop Tunnel Parts Washer provides multi-stage cleaning.
Parts Washing Equipment

Loop Tunnel Parts Washer provides multi-stage cleaning.

CellMate 200 return-to-front conveyor parts washer includes aqueous spray washing and heated air drying in small-footprint package that has fork lift channels or caster for relocation. Overall dimensions of basic stainless steel machine are 37 x 78 in. Complex components may be fixtured on conveyor to facilitate targeted impingement of spray blow-off nozzles onto hard-to-clean or hard-to-dry...

Read More »
Robotic Transporter moves parts to cleaning tanks.
Parts Washing Equipment

Robotic Transporter moves parts to cleaning tanks.

Programmable TDR-50 automated hoist transport system interfaces with most multi-tank cleaning and processing tank lines and consoles. It handles up to 110 lb of load and part fixtures. Programming is via simple keystrokes, using operating codes and keypad numeric functions. It stores up to 255 steps that can be divided among maximum of 10 programs. LED display indicates operating code and X-Y...

Read More »
Conveyor Parts Washer has modular design.
Parts Washing Equipment

Conveyor Parts Washer has modular design.

Model 600 can include rinsing, air-knife blow-off, and drying. System is offered with Allen-Bradley PLC, variety of sensors and fault indicators, and touch-screen interface. Tanks and process chambers are fabricated from 304 stainless steel, allowing flow-through washer to be used with aqueous spray cleaning chemistries without corrosion. Stainless mesh belt, from 16 to 24 in. wide, transports...

Read More »
Programmable Parts Cleaner washes and dries.
Parts Washing Equipment

Programmable Parts Cleaner washes and dries.

Aqueous Cleaning System has 24 in. wide roller conveyor that carries parts to rotary washer where they rotate at variable speeds on worktable with adjustable, high-pressure spray nozzles at top, sides, and bottom. Parts continue automatically on conveyor to heated dryer, where all moisture is removed. Cyclonic system provides filtration of cleaning fluid and removes particles down to 5 microns.

Read More »

All Topics