Blank Washing System can feed several press lines.
Washing Equipment

Blank Washing System can feed several press lines.

Stand-alone Blank Washing System consists of conveyor belt that transports blanks through washer and lubricator, 2 high-speed shuttles, 4 blank carts that run on RoundTrack® in-floor rail system, and centering station. Detached configuration allows press line to run during washer stoppages. SRLS 2/120 material handling robots enable acceleration rates up to 1,120 m/s², velocities up to 5.5...

Read More »
Pressure Washing Equipment

Steam Pressure Washer has high limit safety controls.

With minimal vibration, electric HSE-1002-SM10 operates at 650 psi in steam mode and has 250° water output temperature. Features include insulated trigger gun; totally enclosed, fan-cooled, electric motor with manual thermal overload protection; and top fired, dual spiral coil with powder coated heat exchanger. Unit also incorporates No. 1 or 2 diesel or kerosene fired burner, direct drive...

Read More »
Stainless Steel Parts Washer cleans large parts.
Parts Washing Equipment

Stainless Steel Parts Washer cleans large parts.

Model PWRB9-36EU features 9 in. wide flat wire belt, rinse and blow-off capabilities, and U-bend design that allows single operator to load and unload parts from one location. Heated cleaning solution is sprayed from multiple adjustable nozzles at top, bottom, and sides of 36 in. long cleaning chamber. Built-in cyclonic filtration equipment provides recycling of liquids for reuse and for...

Read More »
Pressure Washing Equipment

Portable Pressure Washer suits commercial industrial market.

Series CW cold water pressure washer features TEFC electric motor with thermal overload protection, triplex piston pump with ceramic plungers, and dual cogged belt drive system. Powder-coated steel base plates are Â-¼ in. with powder-coated steel tube handles. Mobility is provided by pneumatic tires with tubes. Washer includes rubber isolators, 36 in. steel powder-coated lance with rubber...

Read More »
Pressure Washing Equipment

Cold-Water Pressure Washers utilize TEFC electric motors.

Available in hand-carry or cart-mount models, Series CD is equipped with direct-drive triplex piston pump, built-in low-pressure detergent injection, and stainless-steel/brass unloader with adjustable pressure valve. Washers include 35 ft power cord with GFCI, 25 ft steel wire-braided pressure hose, and 36 in. two-piece insulated wand. Additional features include insulated trigger gun, safety...

Read More »
Cold Water Pressure Washer offers 5,000 psi cleaning power.
Pressure Washing Equipment

Cold Water Pressure Washer offers 5,000 psi cleaning power.

Series MP includes 3 models powered by 11, 13, and 24 hp Honda gasoline engines. All feature 1Â-¼ in. steel roll cage with lifting eye, 50 ft high-pressure hose, and 24 in. hose guard. Units ride on steel chassis with 2 or 4 pneumatic tires. Spring-loaded, insulated trigger gun features straight-through pressure wand for remote operation of spray. Washers are suited for descaling flow lines...

Read More »
Parts Washer fits most automotive parts.
Parts Washing Equipment

Parts Washer fits most automotive parts.

Featuring 40 in. high wash cabinet and 28 in. wide rotating turntable, front-load Cuda 2840 uses 3 hp, vertical sealless pump for 50 gpm/45 psi cleaning power. Roll-in, no-drip door facilitates loading and unloading. With load capacity of 750 lb, washer offers automatic low-water shutoff, sloped tank, 12 in. SS disc oil skimmer, and removable 20-mesh debris screen that prevents loose parts and...

Read More »
Aqueous Parts Washer handles automotive parts.
Parts Washing Equipment

Aqueous Parts Washer handles automotive parts.

Model 7320 top-load automatic parts washer features 18 in. working height and 25 in. rotating turntable. Parts, once positioned in turntable basket, are sprayed with hot water and biodegradable detergents. Unit comes with 60 min washer timer, oil skimmer, and 3 hp vertical seal-less pump that flushes parts with flows up to 50 gpm at 45 psi. Water temperature is thermostatically controlled, heated...

Read More »
Parts Washer Sink features stainless steel construction.
Parts Washing Equipment

Parts Washer Sink features stainless steel construction.

Portable Rebel hot-water, parts-washer, Model REB-3626D, features 36 x 26 in. sink, tank, and cabinet made of 304 stainless steel; vertical, seal-less pump that tolerates particles in wash water; and 4 industrial-duty casters. Below sink, 21 gal sump is totally enclosed for heat retention purposes. Trigger-activated spray gun lets users clean parts without having to remove them, while...

Read More »
Aqueous Parts Washer cleans parts on assembly line.
Parts Washing Equipment

Aqueous Parts Washer cleans parts on assembly line.

Single-stage, Mini-Max pass-through parts washer features 16 in. wide steel conveyor belt that carries parts through wash tunnel where they are blasted with hot water spray from 360° spray manifold. Conveyor belt, made of 1 x 1 in. flat wire mesh, can be adjusted to move at speed of up to 8 fpm. Water is heated by three 9 kW tubular heating elements to temperature up to 140°F. The 5...

Read More »
How SpinSelect Can Save You Time and Money
Sponsored

How SpinSelect Can Save You Time and Money

Thanks to the unique SpinSelect™ Multi-Pocket selectable quick change tool holder, it's time to rethink the range, complexity and volume of parts that your lathe can produce. Our Spin-Select™ tool was created to increase productivity and consistency by decreasing downtime associated with lathe cutting tool and insert setups or changeovers. This product is a game-changer for the industry and we're pleased to show you why.

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers