Vises

Clamp Vises are suited for multi-face machining.
Vises

Clamp Vises are suited for multi-face machining.

MC-series Mini Clamp Vises allow clear tool access to 5-out-of-6 workpiece sides. Constructed to promote rigidity, products enable machining of complicated workpieces in single clamping operation. Manual and hydraulic versions come with 60 mm wide jaw and 3,400 lb max clamping force. Concentric type comes in 3 sizes, with 60, 100, and 125 mm jaw widths and 3,400-7,800 lb clamping forces.

Read More »
Vises

Machinist Vise does not require add-on power source.

Using shop air-pressure to produce up to 6,000 lb of clamping force, MVP5 features built-in power intensifier that eliminates need for add-on power sources. Set-ups are repeatable within .001 in., and 90Â-º indexable jaws provide users with 4 machinable sides and are both of anti-lift and quick change design. Jaw sets are available in aluminum or steel.

Read More »
Vises provide quick change fixturing.
Vises

Vises provide quick change fixturing.

Available with 4 and 6 in. jaw widths, BallLock Production Vises provide workholding solution for vertical machining centers. Jaw changeovers take less than 1 min, and BallLock(TM) Mounting System in base permits 1 min changeover of vises. Base features interlocking jigsaw pattern that permits multiple vises to nest closely together, and flow-through design lets chips and fluids escape. Jaws are...

Read More »
Vertical Vise is used with wire EDM machine.
Vises

Vertical Vise is used with wire EDM machine.

Incorporating 2 clamping jaws that require only turning of central screw for tightening, H4538 vise provides positive clamping of 1 or 2 independent workpieces in same set-up. Workpiece height ranges are 2.36-3.74 in. and 3.15-4.53 in., with latter height achieved by relocating clamping jaws at higher level. Jaws can be inverted to provide clamping range of 0.79-2.36 in., and removable side stops...

Read More »
Jaw Vises provide repeatable clamping to 0.001 in.
Vises

Jaw Vises provide repeatable clamping to 0.001 in.

Equipped with machinable jaws, HDL vises have quick change jaw feature and 4 in. hard jaw opening for both clamping stations. They can be converted from manual to hydraulic operation and have spring pre-load design that facilitates part loading. Double station vises, measuring 21 x 6 in., deliver up to 6,316 lb of clamping force at 70 lb of torque for manual model and 7,800 lb at 5,000 psi for...

Read More »
Bench Vise operates in vertical or horizontal positions.
Vises

Bench Vise operates in vertical or horizontal positions.

Made of cast steel with replaceable jaw plates, Model PHV859A is rated at 5 tons with 8 in. wide jaws that open to 8 in. It uses hydraulic pressure to close jaws and spring to open them. Foot-controlled pump offers hold and retract features along with air speed control valve to close jaws quickly or slowly for addditional safety. Hands-free operation facilitates repetitive applications.

Read More »
Concentric Clamping Vises suit space-restricted areas.
Vises

Concentric Clamping Vises suit space-restricted areas.

With mono-block design, PZS pneumatic clamping vise and HZS hydraulic clamping vise have no interface between cover and base body. Mechanical seal avoids chip contamination of jaw guides, and central lubrication system protects base jaws and wedge hook system against wear. Due to double air connections on bottom side, PZS can be turned 90° to change clamping orientation. Both versions are...

Read More »
Stationary Vise offers multiple part clamping.
Vises

Stationary Vise offers multiple part clamping.

Available in 3 lengths, KONETEC KSM system consists of corrosion-resistant 65 or 90 mm wide clamping rail with vertical serration on inner side that allows jaws to be positioned with one hand. Based on wedge-hook principle, vise jaws are reversible and have smooth or serrated surface. Since no chips can jam rails, system is protected against damage and wear. Vise has mounting bores for assembly...

Read More »
Concentric Vises clamp odd-sized workpieces.
Vises

Concentric Vises clamp odd-sized workpieces.

Self-centering, all steel vises position and clamp workpieces on defined symmetrical axis, allowing for any contours. Available in 3 sizes, they offer clamping repeatability of ±0.01 mm and can be used in any mounting position. Compact units provide constant length and use application-specific jaws. Spindle area is protected from dirt, chips, and coolant. Applications include machining...

Read More »
Vises offer repeatable part clamping solutions.
Miscellaneous Fixtures

Vises offer repeatable part clamping solutions.

High Density Long Vise has two 4 in. capacity stations with hard jaws that provide repeatable clamping up to 0.001 in. Manual model delivers up to 6,316 lb clamping force at 70 lb torque, while hydraulic model provides 7,800 lb of force at 5,000 psi. Suited for holding very large parts, Model D810 has 10 in. jaw opening and 11,600 lb clamping force. Available in 4-face and 2-face models,...

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers