New: Buy Now on Thomas and Pay Over Time with Credit Key   Learn More

Valve Controller Trio satisfies various requirements.

Valve Controller Trio satisfies various requirements.

IN-Series interface units include three controllers: IN-23 Y 3 Proportiontal Controller uses control action that progressively closes valve. IN-VCC valve current controller interfaces between process loops and control valves; it accepts 4-20mA control signal and uses this to regulate current applied to valve. Phasecut controls Staefa valves. It modulates valve using 0-20V phase-chopped output...

Read More »
Plastic Valve is stronger than UL requirements.

Plastic Valve is stronger than UL requirements.

Series 40 valve is molded from thermoplastic, has molded-in mounting bracket, survives 2,000 psi hydrostatic test, and has 300 psi maximum pressure rating. Suitable for pneumatic applications, it is available in all standard voltages including 24 VAC transformer power. Options include bracketless version, and full porting for three-way version. Valve is over molded with electrically and thermally...

Read More »
Lubrication System is designed for stamping presses.

Lubrication System is designed for stamping presses.

MicroCoat Lubrication System ensures that stock is always coated with even film of oil. It uses precision spray valves and LVLP (Low Volume Low Pressure) air to apply consistent coat of oil without dry spots, dripping or waste. Valve operation is regulated with pneumatically operated controller. Individual flow controls allow each valve's output to be adjusted independently and provide control...

Read More »
Safety Valves are suitable for use in piping systems.

Safety Valves are suitable for use in piping systems.

Figure 32, 42 and 42A Safety Valves feature stainless steel bases and discs, which provide long life and corrosion resistance. ASME Section I and VIII approved valves feature two-ring control for dependable pop action, seat tightness and repeatability. Cast bronze threaded valves with stainless steel base and disc are available in sizes ranging from 1/2 to 2-1/2 in. for pressures to 300 psi and...

Read More »
Isolation Valves suit tight-fit applications.

Isolation Valves suit tight-fit applications.

Model KV-2 inert, manifold-mount, solenoid-operated, two-way, normally closed isolation valves measure 6 mm in width. They have internal volumes of 10 microL at inlet and outlet and virtually zero dead volume. KV-2 valves feature all inert, internal wetted parts that are diaphragm isolated from coil assembly and other metallic parts. They are suitable for low volume fluidic systems.

Read More »
Diverter Valves handle pressures from 0 to 15 psig.

Diverter Valves handle pressures from 0 to 15 psig.

Diverter Valves are constructed with cast-iron body and end plates, with one-piece ductile iron rotor to hold critical dimensions and resist abrasion. Features include guarded actuators, ledge design that directs material, and triple protected bearings. Available control options include manual, air cylinder, air operated rotary actuators, and electric actuators. Diverter valves are available in...

Read More »
Control Valve offers operating pressure up to 4,600 psi.

Control Valve offers operating pressure up to 4,600 psi.

Duplomatic DS5 directional control valve is a high-performance, five-chamber, NFPA-Standard valve with flow capacity to 40 gpm. Standard features offer a variety of spool configurations including a tandem center model capable of P to T flows of 27 gpm at 2,000 psi. Soft shift option can reduce operating shock and minimize valve and system failure. Coils are standard with plugs to accept DIN 43650...

Read More »
Proportional Valve controls pneumatic pressure.

Proportional Valve controls pneumatic pressure.

Compact Model VP-22 provides variable pressure output in response to a 0 to 10 Vdc or 4 to 20 mA analog control signal. Integral pressure sensor provides closed-loop response. Direct plug-in pneumatic connections accept flexible tubing, eliminating need for pipe fittings. It has scalable pressure output, adjustable damping, low power consumption and LED status indication. Available in full-scale...

Read More »
Ball Valves are used for clean-in-place applications.

Ball Valves are used for clean-in-place applications.

Actuated Ball Valves are constructed of thermoplastics and feature trunnion design to withstand CIP processes. Shafts are strengthened with stainless steel rod. Teflon seats are energized with O-rings, and no metal parts are exposed to process liquid. Actuators are available with electric or pneumatic operation. Both are built from corrosion-resistant thermoplastics and are water and dust-tight...

Read More »
2-Way Poppet Valves feature bubble tight shut-off.

2-Way Poppet Valves feature bubble tight shut-off.

SV72 Series 2-way inert balanced-poppet solenoid valves are designed to control corrosive fluids by isolating metal components from operating media. They employ two rolling diaphragms that act as isolating barriers and balancing areas. SV72 valves feature bubble tight shut-off and are mountable in any position. They offer pressure ratings of 100 psi with a Cv of 4.0. Valves are available with 115...

Read More »
Tekna Manufacturing LLC Announces NFPA 99 Compliant Model 7200 Multiplace Chamber
Sponsored

Tekna Manufacturing LLC Announces NFPA 99 Compliant Model 7200 Multiplace Chamber

Tekna is a leader in Monoplace and Multiplace Hyperbaric Chambers for Hyperbaric Oxygen Therapy (HBOT), offering products that set the standard for quality and innovation. Our new 7200 series of multiplace chambers is a state-of-the-art system that integrates advanced engineering with a plethora of features and options making it the industry's premier HBOT system. To learn more, see our video.

Read More »

All Topics