Transformers

Power Transformers suit HVAC applications.

Power Transformers suit HVAC applications.

UL 1585 Class II approved HVAC/R power transformers incorporate split bobbin design and UL Class B rated insulation material. Individually boxed units, suited for industrial control applications, offer dielectric Strength of 2,500 V and 18 AWG, 6 in. UL wire leads. Foot and Multi-mount versions are offered with voltages from 40-50 VA with primaries from 120-240 V and secondaries from 2.5-24 V....

Read More »
Transformers save space in power applications.

Transformers save space in power applications.

Series 786 pulse transformers employ toroidal construction and offer minimum primary inductance values between 100 Â-µH and 10 mH. Winding configuration options are 1:1, 1:1:1, 2:1. 1 CT:1, and 1 CT:1CT, while DC resistance values range from 0.17-1.34 ohm. Surface mount and through-hole versions are offered and are suitable for line coupling, matching, and isolation applications. Fully...

Read More »

Current Monitor measures high currents with fast risetime.

Model CM-1-MGS5 Wide Band Current Monitor features risetime of 20 nanoseconds and 3 dB bandwidth, which extends from 0.7 Hz to 25 MHz. Sensitivity is 10 mV/A and saturation is 5 As. Using inner diameter of 3.2 cm, unit monitors AC and pulse currents without physically contacting conductor, eliminating ground-loops, and interference noise. Electrostatically shielded, monitor provides output...

Read More »
Clamp-On Current Transformer monitors power quality.

Clamp-On Current Transformer monitors power quality.

Rated 200 A, current transformer provides frequency response of up to 10 kHz, making it suitable for measurement of harmonics. With accuracy of 1% of reading, product accommodates cables up to Â-¾ in. dia. Capable of measuring power for 1- and 3-phase circuits, unit is suited for measuring current commonly found in factory and office distribution wiring. When connected to Portable Power...

Read More »
Pad-Mount Substations consist of building-block units.

Pad-Mount Substations consist of building-block units.

Substation components include parallel transformers, KyleÂ-® RVAC 10T and source transfer switchgear, step-voltage regulators, Kyle 12 vacuum fault interrupter switchgear, Kyle PWE/PWVE reclosers, capacitors, reactors, and control enclosures. Components can be easily added or subtracted and are suitable for severe weather conditions; for developing areas where existing substations can no...

Read More »
Transformer delivers 0.5 W continuous power.

Transformer delivers 0.5 W continuous power.

Model 4283-1400 Miniature High Voltage Output Transformer provides typical operating frequency of 25 kHz and offers up to 800 Vdc output. Surface-mount, application specific DC-DC unit is .495 x .495 x .36 in. With external drive circuitry and internal diodes, minimum efficiency for DC input to DC output is 60%. Transformer can be custom-configured to meet variety of military, medical, and...

Read More »
Isolation/Power Transformers suit medical applications.

Isolation/Power Transformers suit medical applications.

AW Series Toroidal Isolation Transformers and AM Series Toroidal Power Transformers are recognized under UL544 and IEC601-1 safety standards. With power ratings from 100 VA to 3000 VA, 50/60 Hz, transformers can be supplied to meet custom requirements without voiding existing safety recognitions. Toroidal transformers have lower mechanical noise and output impedance than stacked laminated...

Read More »
Transformers suit high-density PC board applications.

Transformers suit high-density PC board applications.

Surface-mount transformers, with 0.39 x 0.38 x 0.50 in. footprint, optimize the ADSL and G.SHDSL capabilities of Titanium(TM) G24 and Octane chipsets. Components comply with UL 1950 and EN60950 to provide basic insulation barrier with working voltage of 150 Vrms and operating temperature range of -40 to +85Â-

Read More »
Printed Circuit Power Transformer is suited for world market.

Printed Circuit Power Transformer is suited for world market.

SPW-3500 Series incorporates independently isolated winding, lead breakout isolation tapes, and epoxy resin impregnation. Dual winding primaries and secondaries offer input voltages of 115/230 V, 50/60 Hz and output voltages from 5.0 to 120 Vac at 6.0 VA. UL 94V0 split-section bobbin and shroud assembly meets creepage and clearance minimums found in world markets. HIPOT rating from primaries to...

Read More »

All Topics