Tools

Angle Grinder offers tool-less wheel changes.
Tools

Angle Grinder offers tool-less wheel changes.

WE14-150 Plus with Vario-Constamatic full-wave electronic speed control, maintains constant speed while operating during maximum load and no-load conditions. It is rated at 1,400 watts, and operates at 6,000 to 9,000 rpm with 12.0 A motor. Maximum wheel diameter is 6 in. Grinder includes 2-position side handle, S-automatic safety clutch, winding protection grid, and thermal overload protection.

Read More »
Tools

Long Jaw Pliers reach into difficult places.

Multi-Nut Plier is made of stainless steel with cushion PVC grips. It can tighten smaller nuts and bolts, holds hard-to-reach heads when tightening bolts, and has V-shaped jaws on sides and end. Tool is suitable for home or professional use by mechanics, repairmen, electricians, and hobbyists.

Read More »
Hammer Drill suits heavy-duty applications.
Hand Held Drills

Hammer Drill suits heavy-duty applications.

SBE750 1/2 in. hammer drill, with tightening torque of 159 in. lbs., provides 3/4 in. capacity in concrete, 1/2 in. capacity in steel, and 1 1/2 in. capacity in soft wood. Winding-protection grid deflects airborne debris away from armature windings, and variospeed, full-wave, electronic speed control allows for infinite speed variations. Rated at 6.2A with input rating of 750W, SBE750 offers...

Read More »
Wrench provides 2 tools in 1 for plumbing installations.
Tools

Wrench provides 2 tools in 1 for plumbing installations.

OneStop(TM) consists of smaller wrench stored within tubular body of larger wrench. It provides all exact size surface wrenches needed for angle stop and compression coupling installation. To use, smaller wrench is unscrewed and withdrawn. Lug at end of smaller wrench can be inserted into riser mouth of angle stop for pointing and stability. Larger wrench can be used to tighten back compression...

Read More »
Ports

Load Port handles 300 mm semiconductor wafers.

Automated IsoPort(TM) has front-opening-unified-pod (FOUP) tool carrier interface, servo-controlled motion, latchkey, and carrier sensing. Tool throughput is 8 sec, from carrier arrival to first-wafer access. Contamination control conforms to ISO Class 1 particle level, and eliminates triboelectric charge buildup on carrier door. Optional gas purge ports provide an inert ambient environment for...

Read More »
Duct Rodders come in any length.
Miscellaneous Cleaning Equipment

Duct Rodders come in any length.

Available in 1/4, 5/16, 7/16 and 9/16 in. dia, duct rods are supplied in lengths specified by customer. Fiberglass rods, made from E-Glass+ Vinylester, provide high tensile strength and flexibility. Glass-fiber core is reinforced with high-strength resin, and reinforced wrap is added before UV-stabilized, wear-resistant, protective propylene coating is applied. Rods are wound on lightweight,...

Read More »
Intelligent Torque Tools communicate with controller.
Tools

Intelligent Torque Tools communicate with controller.

Series 66 includes right-angle flanged head, right-angle sliding spindle, offset, tubenut, crowfoot, and pistol-grip nutrunners. Standard right-angle configurations are available in 25 to 200 Nm range, while sliding spindle tools come in 40 to 160 Nm. All contain internal microprocessor inside tool handle. Setup and calibration is automatic upon connection of tool to company's CS4000 or CS5000...

Read More »
Crimping Tools offer high speed operation.
Hand Crimpers

Crimping Tools offer high speed operation.

Y500CTHS L'IL CRIMP(TM) Hydraulic crimp tool requires only 7 strokes to advance ram prior to crimping lug. It features wire range capacity of #8 AWG through 500 Kcmil copper, and permanent D3 die groove. BCT500HS BATOOL(TM) incorporates Makita tool base, motor with replaceable brushes, and 3-piston pump. Both crimp tools accommodate all W series dies and offer 180 deg rotating, stainless steel...

Read More »
Cable Ties are available in weather-resistant designs.
Cable / Wire Ties

Cable Ties are available in weather-resistant designs.

Tie-Max(R) cable ties are designed for mounting and non-mounting applications. Tensile strength ranges from 18 to 175 lb, with cable lengths of 3.78 in. to 30 in. Tensile strength of mounting cables is 18 to 50 lb, in lengths of 3.94 in. to 8.07 in. Weather-resistant Tie-Max ties have UV-resistant Carbonate A added. Pocket-sized hand tools and tie guns tighten and cut cable.

Read More »
Inserts combine grooving and turning.
Cutting Tool Inserts

Inserts combine grooving and turning.

GROOVE 'N TURN(TM) inserts are available in 2 sub-micron grain carbide grades, DM-2(R) for steel and interrupted cutting, and DM-5(R) for aluminum and other non-ferrous alloys. Groove width sizes include .020, .030, .040, .060, .080, .100, and .125 in. with either sharp corners or .007 in. corner radius. Uncoated and TiN coated inserts are in stock. TiCN, TiAIN and diamond coatings are also...

Read More »
How SpinSelect Can Save You Time and Money
Sponsored

How SpinSelect Can Save You Time and Money

Thanks to the unique SpinSelect™ Multi-Pocket selectable quick change tool holder, it's time to rethink the range, complexity and volume of parts that your lathe can produce. Our Spin-Select™ tool was created to increase productivity and consistency by decreasing downtime associated with lathe cutting tool and insert setups or changeovers. This product is a game-changer for the industry and we're pleased to show you why.

Read More »

All Topics