Testing Services

Testing Services

National Industrial Hygiene Testing

Environmental Safety Consultants, Inc. is pleased to announce industrial hygiene testing services are now being offered throughout the continental U.S. No longer restricted to Florida, ESC is now providing top quality industrial hygiene services to manufacturers across the country. Over the last two years, ESC began expanding its market area. Projects have now been completed in Texas, Indiana,...

Read More »
Engines

GE Announces Co-Development Project for New Asset Performance Management Software Solution for Its Waukesha Gas Engines

• Co-Development Project with Crestwood Midstream Partners LP to Use GE's Asset Performance Management Solution Powered by Predix* • New Software Platform to be Installed in 16 Waukesha VHP Gas Engines at Three Compressor Stations in the Marcellus Shale Area of West Virginia WAUKESHA, WISC. — GE (NYSE: GE) today announced that Crestwood Midstream Partners LP (Crestwood) is the...

Read More »
Fasteners

Laboratory Testing Inc. Exhibiting At National Industrial Fastener and Mill Supply Expo

HATFIELD, PA – Laboratory Testing Inc. (LTI) will once again be exhibiting at the National Industrial Fastener and Mill Supply Expo (NIFMSE) in Booth #816 on October 21 – 23, 2015 at the Sands Expo Center in Las Vegas, NV. The Lab will be showcasing its broad range of fastener testing, dimensional inspection and failure analysis capabilities. LTI is a full-service materials testing,...

Read More »
Testing Services

Laboratory Testing Inc. Exhibiting at Titanium USA 2015

Laboratory Testing Inc. (LTI) will be exhibiting at Titanium USA 2015 in Booth #712 from October 4th through October 7th at the Rosen Shingle Creek Golf Resort in Orlando, Florida. LTI offers a wide range of mechanical testing, metallography and chemistry services that can evaluate material composition and the effects of heat treatments on titanium materials. Ultrasonic testing and other...

Read More »
Design Services

Mentor Graphics Drives Next-Generation, Low-Power Verification with UPF Successive Refinement Methodology

WILSONVILLE, Ore. - Highlights: Â- Ã‚ Â  --  The Unified Power Format (UPF) Successive Refinement Methodology enables         the incremental specification and early verification of power management         intent.     --  The...

Read More »
Certification Services

Laboratory Testing Inc. Announces Continuation of A2LA Accreditation and Expanded Scope

Laboratory Testing Inc. (LTI) was successfully audited and approved for continued accreditation by the American Association for Laboratory Accreditation (A2LA) in accordance with ISO/IEC 17025-2005. The scope of LTI's A2LA accreditation was also expanded for mechanical testing and calibration services. Bore micrometers were added to the calibration certificate. The expanded mechanical testing...

Read More »
Material Testing Service uses microwave heating.
Testing Services

Material Testing Service uses microwave heating.

As part of Ignite™ program, Harper International offers Microwave Testing for all non-metallic and electrically non-conducting materials in temperatures from 600–1,800°C. Typical applications include ceramic processing, powders, shaped ceramics, activated carbon, battery materials, and food processing. Microwave heating provides significant benefits over conventional heating since...

Read More »
North Carolina State University
Switchgear

North Carolina State University

On 08/01/2015 Carolina Precision Switchgear performed testing services on three Siemens main switchgear assemblies at the North Carolina State University. Testing services included transformer turns ratio test (TTR), megger testing transformers, circuit breaker testing, relay testing (primary injection) and switchgear inspections. Found a few issues, but overall equipment in good condition.

Read More »
Chambers

Northwest EMC Adds Antenna Pattern Measurements and Over the Air Testing at its Minnesota Testing Lab

Northwest EMC, a leader in the EMC testing industry, has announced the addition of a new OTA/3D Antenna Test Chamber at its Minnesota testing lab. The new test chamber is designed for fully compliant radiated wireless antenna measurements over the frequency range of 400 MHz to 6 GHz. Testing facilities around the world have seen increasing demand for Antenna Pattern Measurements and Over the Air...

Read More »
Bonders

Sonobond's Ultrasonic Bonding Technology Increasingly Essential for Ensuring Reliable Body Armor Assembly

More than 30 Leading Manufacturers Use Sonobond Equipment to Achieve Improved Production Speed, Product Durability, Cost-Effectiveness and Compliance with Tough NIJ Standards WEST CHESTER, Pennsylvania — With armed services personnel, emergency responders, law enforcement officers, and others exposed to more and more perilous circumstances, reliable body armor is absolutely essential for their...

Read More »

All Topics