Stepper Motors

Stepper Motors

Closed-Loop Stepping Motors are rated for continuous duty.

Featuring stator and rotor assembly techniques that minimize power loss in motor, AR Series utilizes AlphaStep closed loop control technology, rotor position sensor, and alarm signal to maintain positioning capability. Drivers accept AC/DC voltage input and come in 1.65, 2.36, and 3.35 in.Â-² motor frame sizes, all available with standard shaft, 3 types of gearheads with various gear ratios,...

Read More »
Stepper Motors are available in hollow shaft versions.
Stepper Motors

Stepper Motors are available in hollow shaft versions.

Hollow shaft versions of h3 stepper motors allow wires or other media to be routed through motor shaft. With neodymium iron boron magnets to optimize torque density and bearing retainer/o-ring to help minimize motor noise, 1.8° step motors also feature aluminum housing for maximized heat dissipation and minimized power consumption. They are offered in NEMA 17, 23, and 34 frame sizes, with...

Read More »
Linear Motors feature modulated gas control.
Stepper Motors

Linear Motors feature modulated gas control.

Integrating motor and valve, Linear Motor Series provides proportional control of gas flow for energy-efficient gas heating. Synchronous model provides 10 mm displacement at 115 V, linear step speed of 0.833 or 1.67 mm/sec, and output force of 27-45 N. Featuring dual safety system, 2 stepper-based models incorporate -7.5° and -15° step angle, linear step displacement of 0.0167 and...

Read More »
Stepping Motor has 12-60 Vdc integrated driver.
Stepper Motors

Stepping Motor has 12-60 Vdc integrated driver.

NEMA size 23 brushless 1.8° stepping motor MDrive23Plus is available in 3 versions; microstepping with step and direction input, motion control with intelligent programmable controller, and speed control with velocity controller. Featuring extended operating range of -40 to +85°C and small footprint, product is available with various options to meet specific application requirements...

Read More »
CMAA Crane Buyer's Guide
Sponsored

CMAA Crane Buyer's Guide

CMAA has organized this Buyer's Guide to promote standardization and to assist prospective buyer's of electric overhead traveling cranes in selection of equipment most suitable for their applications.

Read More »
Motor/Drive Packages offer NEMA size 14 motor option.
Stepper Motors

Motor/Drive Packages offer NEMA size 14 motor option.

Suited for limited-space applications, MDrive14Plus products integrate NEMA size 14 brushless 1.8° stepping motor with electronics. Units are 2 in. high x 1.4 in. wide, with lengths of 2 in. for single motor or 3 in. for triple motor, which provides holding torque at 36 oz-in. Capable of full 256 x 200 microstepping with 12-48 Vdc integrated driver, MDrive14Plus systems feature extended...

Read More »
Integrated Stepper Motor/Drive operates at up to 1,500 rpm.
Stepper Motors

Integrated Stepper Motor/Drive operates at up to 1,500 rpm.

Model STM23 is size 23 motor and drive, contained in aluminum heatsink housing, with RS232/RS485 interfaces for programming drive using rich instruction set software. Motor operates in closed loop mode and coding can be downloaded to drive or unit can be controlled using commands from attached controller. With supply of 12-80 Vdc and 0.2-5 A peak output current, it is offered in single or double...

Read More »
Stepper Drives Series STM
Stepper Motors

Stepper Drives Series STM

Series STM The STM is a drive+motor+control unit, fusing step motor, drive, and controller technologies into a single device, offering savings on space, wiring and cost over conventional motor and drive solutions. The S" models offer control options such as step and direction, analog input, joystick control, and serial host commands while the "Q" models add the capability of stand-alone...

Read More »
Integrated Motor, Drive suit limited-space motion applications.
Stepper Motors

Integrated Motor, Drive suit limited-space motion applications.

Measuring 1.9 x 1.4 x 2.0 in., MDrive14Plus Microstepping and MDrive14Plus Half/Full Step utilize NEMA size 14 brushless 1.8° stepping motor. MDrive14Plus Half/Full Step suits basic applications requiring no more than half and full step, while MDrive14Plus Microstepping is capable of full (256 x 200) microstepping and features 12-48 Vdc supply input, choice of internal magnetic or external...

Read More »
Permanent Magnet Stepper Motors from Astrosyn Available in Low Volumes
Stepper Motors

Permanent Magnet Stepper Motors from Astrosyn Available in Low Volumes

A wide range of high performance permanent magnet stepper motors has been introduced by motion control specialists Astrosyn International Technology. The use of PM stepper motors offers manufacturers the advantages of simple construction, high thrust and low price. However, unlike with most permanent magnet devices, minimum order quantities from Astrosyn can be as low as a few hundred pieces....

Read More »
Step Motors suit multi-axis applications.
Stepper Motors

Step Motors suit multi-axis applications.

Based on MotionChip(TM) DSP control technology, IS23x-MA Intelligent Step Motors are designed for distributed motion control applications. Motion programming can be done from CAN/CANopen master via PC/PLC, either by using motion library, or directly at motor level, using built-in motion controller and EasyMotion Studio platform. Developed in 2 motor lengths, units offer 1-1.8 Nm permanent output...

Read More »
Precision Fabricating with Over 40 Years of Experience
Sponsored

Precision Fabricating with Over 40 Years of Experience

Quality Sheet Metal specializes in delivering precision, value, and customer service. With a client base that spans many diverse industries and a reputation for excellence that goes back over four decades, our clients know that we can provide the optimal combination of value and flexibility regardless of the challenge. See our video to learn what we can do for you. Through investments in state-of-the-art design, manufacturing, and quality control systems, Quality Sheet Metal remains focused on maintaining a high standard of quality, customer service, and competitive pricing. With an emphasis on customer satisfaction, Quality Sheet Metal is dedicated to establishing long-term partnerships, similar to the ones they currently have with their valued clients. If you're looking for a new partner with extensive capabilities in sheet metal fabricating and finishing, look no further.

Read More »

All Topics