New Sensors, Monitors & Transducers Products

Machine Monitoring System provides predictive maintenance.

Series XMÃ-® offers distributed protection and monitoring using modules for EtherNet/IP(TM) communication, low-speed vibration, and spike energy measurements. Gathered information allows maintenance personnel to identify developing faults and correct problems before downtime events occur. Hot-swappable modules communicate with programmable controllers or distributed control systems through...

Rotary Encoders provide 9-bit resolution.

Miniature magnetic encoders are frictionless units available in absolute, incremental, or linear output formats. Speeds of over 30,000 rpm can be achieved with measurement accuracy better than 0.7Ã-

Portable Ultrasonic Flaw Detectors offer on-board charging.

Models USN 58L, USN 58R, and USN 60 will run for at least 8 hours using Lithium Ion battery pack, which is contained in same battery tray and can be installed in the field via 4 knurled screws. Battery pack does not have to be removed to recharge and can be charged externally if spares are needed for continuous use. Charger also serves as AC power supply.

Point Level Sensor withstands harsh environments.

Model NR60 monitors minimum or maximum levels of liquids by detecting changes in electrical capacitance in field surrounding probe. Featuring brass housing and solid-state electronics, unit withstands 50 g mechanical shock, 25 g vibration, immersion, and temperatures to 125Ã-

Direct Acting High Speed Servo Valve (DASV)

Download this paper to learn about how high performance servo valve's can be used in your most demanding hydraulic and pneumatic applications.

Accelerometer measures extremely high frequencies.

Single-axis, ICPÃ-® Model 352A60 features extended flat frequency response of 5-60,000 Hz Ã-

Analog Inductive Prox Sensors monitor moving targets.

Ultralinear(TM) inductive proximity sensors utilize linear analog feedback signal that is proportional to target distance from sensor face and provides resolution down to 1.5 microns. Triple-setpoint models employ onboard microprocessor that allows teach-in of up to 3 output on-zones. Linearity/temperature-compensation and calibration ASICs enable repeatability of less than 3% and temperature...

Leak Test Systems offer real-time process control.

Falcon Leak Test System simultaneously locates and calculates leak rate. Using Intelense technology with sensitivity to 10-5 sccs, system bridges gap between pressure decay technology and helium vacuum mass spectrometry. Sentinel M24 Leak Test Instrument, offered in single- or multiple-station configurations, includes VFD graphic display, operator interface, and ability to communicate directly to...

Temperature Sensors help reduce process variation.

INFOSENSE-P(TM) Plug and Play Sensors link customer's application to NIST-traceable calibration lab. They incorporate EEPROM memory chip, preprogrammed with sensor's part number, manufacturing information, and full range temperature calibration. When sensor is wired to IEEE 1451.4 compatible electronics, controller accesses information provided and performs full high-order curve fit to correct...

Flammable Gas Leak Detector offers one button operation.

Able to detect combustible gases with concentrations down to 50 ppm, Model C052 incorporates backlit display that switches on in low-light areas. Unit displays flammable gas levels at 100, 1,000, and 10,000 ppm, and audible indicator increases pitch tone as concentration of gases goes up. Meter provides auto zero on start up, 5 sec response time, battery status display, and dimensions of 1.5 x 10...

Pressure Transmitter suits cleanroom and HVAC applications.

RosemountÃ-® 951 Dry Gas Differential Pressure Transmitter features 4-20 mA/HartÃ-® output, enabling user to calibrate, re-range, and configure in the field. It allows 40:1 turndown and provides stability of 0.125% of URL per year. Transmitter is suited for ultra low differential pressure measurement applications, such as control and monitoring of cleanroom pressures and airflows in HVAC...

Custom Fabrication & Machining Services with Over 30 Years of Experience

As a trusted manufacturer to customers across a broad range of industries, Key Gas Components is a premier provider of CNC machining and tube fabrication. Our entire organization is quality driven and customer-centric, with broad-based manufacturing capabilities that can accommodate the most challenging requirements. See our video to learn more.