Torque Sensors are designed for low torque applications.
STS2220 rotary shaft torque sensors are available in capacities from 1.0 to 10.0 Nm. They feature one-piece outer housings and pre-lubricated bearings, and accept either AC or DC excitation voltage for compatibility to most readout instruments. Units have 1.5 mV/V nominal output at rated capacity, bridge resistance of 350 ohms, maximum speed of 10,000 rpm, and non-linearity of +/- 0.1% of full...
Read More »Rotary Torque Sensors eliminate need for slip ring.
Model 01279 line of rotary torque sensors use non-contact infrared digital signal transmission, eliminating maintenance and wear problems of conventional slip ring technology. Sensors have high level analog output to represent torque load. They can be used as drop in replacements for many existing rotary torque sensors.
Read More »
Fixed Gas Sensor features 2 gas monitoring points.
WorksAlone 2(TM) fixed-point gas detection monitor, incorporating dual-sensor design, displays gas concentration levels and signals alarm conditions when programmed alarm points have been exceeded. It provides 1 or 2 gas monitoring points installed on-board or remotely from electronic controllers. Features include automatic, non-intrusive calibration and split-screen, extended-temperature LCD...
Read More »
Fixed Gas Sensor features 2 gas monitoring points.
WorksAlone 2(TM) fixed-point gas detection monitor, incorporating dual-sensor design, displays gas concentration levels and signals alarm conditions when programmed alarm points have been exceeded. It provides 1 or 2 gas monitoring points installed on-board or remotely from electronic controllers. Features include automatic, non-intrusive calibration and split-screen, extended-temperature LCD...
Read More »
Comparing Casting Processes
This white paper compares and contrasts common casting processes.
Read More »
Sensor converts shaft to torque sensor in 15 minutes.
Model 1650B Snap-On Rotary Torque Sensor clamps onto drive train to take measurement data. It does not break into drive train to install in-line torque cell, and requires no professional installation. Model 1650B comes pre-calibrated. Installation requires users to clamp on 2 halves of sensor shell, position antenna, and connect wireless receiver. Available for shaft diameters from 2.5 to 15 in.,...
Read More »
Sensor converts shaft to torque sensor in 15 minutes.
Model 1650B Snap-On Rotary Torque Sensor clamps onto drive train to take measurement data. It does not break into drive train to install in-line torque cell, and requires no professional installation. Model 1650B comes pre-calibrated. Installation requires users to clamp on 2 halves of sensor shell, position antenna, and connect wireless receiver. Available for shaft diameters from 2.5 to 15 in.,...
Read More »
Tranducer Kit is fully re-rangeable.
LOS ANGELES, CALIFORNIA, October 2001 - Validyne Engineering eliminates the need to purchase multiple pressure transducers with the introduction of the DPl5 10-In One" Pressure Transducer kit. The fully "re-rangeable" DP15 pressure transducer kit contains a variable reluctance sensor with 10 replaceable sensing diaphragms, 0-rings, bleed screws, gaskets, an AC power adapter, the CD379 portable...
Read More »
Tranducer Kit is fully re-rangeable.
LOS ANGELES, CALIFORNIA, October 2001 - Validyne Engineering eliminates the need to purchase multiple pressure transducers with the introduction of the DPl5 10-In One" Pressure Transducer kit. The fully "re-rangeable" DP15 pressure transducer kit contains a variable reluctance sensor with 10 replaceable sensing diaphragms, 0-rings, bleed screws, gaskets, an AC power adapter, the CD379 portable...
Read More »
Electrochemical Sensors monitor CO, H2S and O2.
XS-R Series has three-electrode design, providing greater specificity to target gases, resistance to over exposure, and stability in presence of changing temperatures, pressures and humidity. Sensors are available for carbon monoxide, hydrogen sulfide and oxygen.
Read More »
Electrochemical Sensors monitor CO, H2S and O2.
XS-R Series has three-electrode design, providing greater specificity to target gases, resistance to over exposure, and stability in presence of changing temperatures, pressures and humidity. Sensors are available for carbon monoxide, hydrogen sulfide and oxygen.
Read More »
ISO-Certified J&D Tube Benders Delivers Rapid Tubeline Fabrication Services
J&D Tube Benders' laser cutting and machining services provide accurate and complex features on tubes of all shapes and sizes. Check out the video to learn more!
Read More »
