Sealants

Flexible Adhesive/Sealant meets USP Class VI requirements.
Sealants

Flexible Adhesive/Sealant meets USP Class VI requirements.

Optically clear, UV-curable UV15X-6 polymer system adheres to various substrates, including plastics and elastomers. Suited for medical device assemblies, single-component urethane formulation is 100% reactive, does not contain any volatiles, and also acts as electrical insulator. Cure is not affected by air or moisture, and cured material exhibits abrasion resistance. Bonds resist exposure to...

Read More »
Miscellaneous Compounds

Semi-Solid Anaerobic Stick Products will not leak or drip.

QuickStix(TM) 534(TM) Hi-Tack Gasket Dressing allows cut gaskets to be positioned and held in place while mating surfaces are aligned for assembly. Product cures at room temperature. Oil resistant QuickStix(TM) 548(TM) Gasket Eliminator® Flange Sealant prevents fluid or gas leaks on rigid iron, steel, and aluminum flanges. QuickStix(TM) 668(TM) Retaining Compound bonds non-threaded...

Read More »
Adhesive/Sealant bonds dissimilar substrates.
Epoxies

Adhesive/Sealant bonds dissimilar substrates.

Cured at room or elevated temperatures, 2-component EP21TDCHT-1 has temperature range serviceability of -100 to +400°F. Compound serves as electrical insulator with volume resistivity of 1014 ohm-cm. Epoxy adhesive/sealant is resistant to vibration, impact, and thermal shock as well as exposure to water, oils, and organic solvents. It has 70 Shore D hardness, 3,000+ psi tensile strength,...

Read More »
Epoxy Adhesive/Sealant/Coating is chemical-resistant.
Coatings

Epoxy Adhesive/Sealant/Coating is chemical-resistant.

Featuring thermal stability, 2-component EP21ARHT-1 is 100% reactive and does not contain any solvents or diluents. It has 2:1 mix ratio by weight and cures at room temperature. Exhibiting minimal shrinkage upon cure, product does not sag or drip on vertical surfaces. Designed to withstand thermal shock and abrasion, it adheres to metals, glass, ceramics, cements, woods, vulcanized rubbers, and...

Read More »
Sealants

Ceramic Sealer provides 1800°F service.

Applied by caulking cartridge, 7030 sealer forms gas tight seals with no objectionable odors or harmful fibers. Free flowing formulations are available for rapid or automatic dispensing applications. Room temperature-cure product bonds to metals, ceramics, door gaskets, tadpole gaskets, and ceramic cloths with no special surface treatment required. Corrosion and erosion resistant coatings are...

Read More »
Epoxy provides high thermal conductivity.
Epoxies

Epoxy provides high thermal conductivity.

Type EP34AN room temperature cure, 2-component epoxy adhesive/sealant, with thermal conductivity of 22-24 BTU/in/ftÂ-²/hr/°F, maintains physical properties after prolonged exposure to temperatures from 400-450°F. It exhibits dimensional stability and electrical insulation properties and can be applied without sagging or dripping. Able to bond to various substrates, 100% reactive...

Read More »
Sealants

Silicone Rubber Sealants suit high-volume manufacturing.

Loctite® 5210 and Loctite® 5211 non-corrosive sealants are used for wire tacking, selective sealing, vibration dampening, and repair/rework applications on PCBs. Thixotropic, moisture curing Loctite® 5210 lets product conform to applied components while remaining where dispensed. Medium viscosity Loctite® 5211 allows material to flow into applied areas and encapsulates...

Read More »
Sealants

Module Sealant suits automotive electronics assembly.

Medium-viscosity, UV- and moisture-curing Loctite® 5252 is designed for post-assembly use on electronic module enclosures. Based on polyether rubber technology, thixotropic sealant withstands temperatures from -40 to +125°C and offers controlled flow. It seals seams without seepage or dripping and allows users to tack material within seconds. Sealant-incorporated fluorescent dye...

Read More »
Sealants

Surfactant-Free Sealant seals porous metals.

HPS(TM) 1000 and 1100 seal microscopic voids in leaking porous metals such as powdered-metal castings and sintered-metal parts through vacuum application process. Both feature resistance to degradation by hydrocarbon solvents, and lubricity that lowers tool wear. Surfactant-free products facilitate washing of impregnated parts and eliminate need for pretreatment of disposed waste rinse water.

Read More »
Room Temperature Curing Epoxy withstands sterilization.
Epoxies

Room Temperature Curing Epoxy withstands sterilization.

Dual-component EP42HT-2 epoxy adhesive, sealant, coating, and casting material withstands repeated sterilizations, including radiation, ethylene oxide, chemical sterilants, and steam. Featuring service operating temperature range of -60 to +450°F, product exhibits chemical resistance and Shore D hardness greater than 75. Properties include mixed viscosity of 3,500 cps and tensile strength...

Read More »
Neagle Choice, LLC Announces New Available Services
Sponsored

Neagle Choice, LLC Announces New Available Services

Neagle Choice has long been known as a quality source for commercial sewing, printing, die cutting, and the manufacturing of a wide range of custom products. Enhancing our service capabilities has been the key to our success, and has driven our growth into many new and exciting markets. Continuing on this trajectory, we now offer precision laser cutting and etching, adding to our long line of manufacturing services. See our video to learn all about it.

Read More »

All Topics