Sealants

UV Curable Compound adheres to plastic, glass, and metals.
Laminates

UV Curable Compound adheres to plastic, glass, and metals.

Flexible, optically clear UV19 cures upon exposure to UV light at ambient temperatures. Compound is 100% reactive, does not contain any volatiles, and offers abrasion resistance and heat stability. With tensile strength in excess of 800 psi and viscosity of less than 300 cps at 75°F, compound is suited for laminating, sealing, and bonding to substrates with different thermal expansion...

Read More »
Valve Lubricant and Sealant resists effects of chemicals.
Lubricants

Valve Lubricant and Sealant resists effects of chemicals.

Dow Corning® 111 heavy-consistency, dimethyl silicone compound maintains serviceable consistency from -70 to +400°F. Acceptable as release agent under FDA 21 CFR 175.300, it carries NSF 51 and NSF 61 approvals. Product can be used as lubricant for rubber and plastic O-rings, water softener and faucet valves, and electronic and ignition systems. It may also be used as sealant in...

Read More »
Assembly Sealant offers instant adhesion.
Sealants

Assembly Sealant offers instant adhesion.

Reactive hot-melt silicone, HM-2500 cures to flexible, weather-resistant silicone seal with UV resistance. It adheres to PVC, aluminum, painted and treated wood, paints, and plastics. High viscosity at room temperature resists flow of material, minimizing sealant squeeze out and clean up. Moisture curing, 100% silicone product is optimized for use with automated dispensing equipment, which...

Read More »
Concrete/Masonry Sealer offers one-step application.
Coatings

Concrete/Masonry Sealer offers one-step application.

Water-based All-Shield® Concrete & Masonry Sealer stops water penetration and damage in concrete, masonry, brick, block, stone, tile, stucco, and adobe. Clear, non-yellowing, VOC compliant formula allows substrate to breathe and water vapor to escape, providing protection for up to 8 years. Mold and fungus resistant, it also protects against freeze/thaw cycles, efflorescence, and alkali....

Read More »
Flexible Adhesive/Sealant meets USP Class VI requirements.
Sealants

Flexible Adhesive/Sealant meets USP Class VI requirements.

Optically clear, UV-curable UV15X-6 polymer system adheres to various substrates, including plastics and elastomers. Suited for medical device assemblies, single-component urethane formulation is 100% reactive, does not contain any volatiles, and also acts as electrical insulator. Cure is not affected by air or moisture, and cured material exhibits abrasion resistance. Bonds resist exposure to...

Read More »
Miscellaneous Compounds

Semi-Solid Anaerobic Stick Products will not leak or drip.

QuickStix(TM) 534(TM) Hi-Tack Gasket Dressing allows cut gaskets to be positioned and held in place while mating surfaces are aligned for assembly. Product cures at room temperature. Oil resistant QuickStix(TM) 548(TM) Gasket Eliminator® Flange Sealant prevents fluid or gas leaks on rigid iron, steel, and aluminum flanges. QuickStix(TM) 668(TM) Retaining Compound bonds non-threaded...

Read More »
Adhesive/Sealant bonds dissimilar substrates.
Epoxies

Adhesive/Sealant bonds dissimilar substrates.

Cured at room or elevated temperatures, 2-component EP21TDCHT-1 has temperature range serviceability of -100 to +400°F. Compound serves as electrical insulator with volume resistivity of 1014 ohm-cm. Epoxy adhesive/sealant is resistant to vibration, impact, and thermal shock as well as exposure to water, oils, and organic solvents. It has 70 Shore D hardness, 3,000+ psi tensile strength,...

Read More »
Epoxy Adhesive/Sealant/Coating is chemical-resistant.
Coatings

Epoxy Adhesive/Sealant/Coating is chemical-resistant.

Featuring thermal stability, 2-component EP21ARHT-1 is 100% reactive and does not contain any solvents or diluents. It has 2:1 mix ratio by weight and cures at room temperature. Exhibiting minimal shrinkage upon cure, product does not sag or drip on vertical surfaces. Designed to withstand thermal shock and abrasion, it adheres to metals, glass, ceramics, cements, woods, vulcanized rubbers, and...

Read More »
Sealants

Ceramic Sealer provides 1800°F service.

Applied by caulking cartridge, 7030 sealer forms gas tight seals with no objectionable odors or harmful fibers. Free flowing formulations are available for rapid or automatic dispensing applications. Room temperature-cure product bonds to metals, ceramics, door gaskets, tadpole gaskets, and ceramic cloths with no special surface treatment required. Corrosion and erosion resistant coatings are...

Read More »
Epoxy provides high thermal conductivity.
Epoxies

Epoxy provides high thermal conductivity.

Type EP34AN room temperature cure, 2-component epoxy adhesive/sealant, with thermal conductivity of 22-24 BTU/in/ftÂ-²/hr/°F, maintains physical properties after prolonged exposure to temperatures from 400-450°F. It exhibits dimensional stability and electrical insulation properties and can be applied without sagging or dripping. Able to bond to various substrates, 100% reactive...

Read More »

All Topics