Repair Compounds

Devcon® R-Flex™ Belt Repair Compound reduces plant downtime.
Repair Compounds

Devcon® R-Flex™ Belt Repair Compound reduces plant downtime.

Devcon® R-Flex™ Belt Repair Compound is formulated to repair holes, tears, gouges, and damaged cold vulcanized splices. This compound forms tough monolithic surface for protecting clip splices. Product can be applied to pulleys with diameters as small as 10 in. and provides long-term adhesion and abrasion resistance. R-Flex increases resistance to crack propagation and is used for coating...

Read More »
Colorite Features New Thermoplastic Elastomer Compound Line for Medical Devices at MD&M East
Repair Compounds

Colorite Features New Thermoplastic Elastomer Compound Line for Medical Devices at MD&M East

Wayne, Pa. (May 2, 2017) - A line of thermoplastic elastomer (TPE) compounds for medical device applications in North America will be featured by Colorite, a Tekni-Plex company, at MD&M East, June 13-15, Jacob Javits Convention Center, New York City, in Booth 1445. Cellene™ TPE compounds are suitable for a wide variety of uses in medical devices, packaging and other regulated markets....

Read More »
The Next Wave of Intelligent Design Automation
Sponsored

The Next Wave of Intelligent Design Automation

In the amount of time it takes to set up a meeting to discuss just one design, engineers can now explore designs exponentially. Generative design has catalyzed a paradigm shift in product development. This shift not only drastically decreases the time it takes to design a product. It also opens the door to design options that might never have been imagined by engineers on their own.

Read More »
Devcon® Dfense Blok™ with Ez Mix Technology Simplifies Wear & Abrasion Protection in Colder Climates
Repair Compounds

Devcon® Dfense Blok™ with Ez Mix Technology Simplifies Wear & Abrasion Protection in Colder Climates

DANVERS, MA - Devcon DFense Blok EZ Mix™ provides the same exceptional wear and abrasion protection as original DFense Blok™, but is easier to mix in colder climates. DFense Blok™ alumina ceramic bead-filled epoxy wearing compound is specially formulated to outperform and outlast traditional epoxy wear and abrasion products - even in the most severe impact and sliding abrasion conditions....

Read More »
Toughened Two Component Epoxy Is Optically Clear and Resists Thermal Cycling
Repair Compounds

Toughened Two Component Epoxy Is Optically Clear and Resists Thermal Cycling

Master Bond EP38CL was developed for bonding, sealing, coating and encapsulation applications that require toughness and durability. With a Shore D hardness exceeding 75, its toughness is a unique property that imparts resistance to rigorous thermal cycling, impact and mechanical shock.Â-  EP38CL cures at room temperature or more quickly at elevated temperatures and has low shrinkage upon...

Read More »
Non-Drip Epoxy can be used in indirect food applications.
Repair Compounds

Non-Drip Epoxy can be used in indirect food applications.

With thick paste consistency, Master Bond® EP21NDFG bonds toÂ- diverse substrates – metals, composites, glass, ceramics, rubbers, plastics – and will not run or sag even when applied to vertical surfaces. Bonds resist thermal cycling as well as chemicals, including water, oils, fuels, acids, bases, and salts. This 2-component, room temperature cure epoxy...

Read More »
Repair Compounds

Bondable, Biocompatible TPEs suit medical device applications.

Pre-tested for compliance with ISO 10993 biocompatibility standards, RTP 6042 MD and RTP 6003 MD Series are naturally opaque, fully colorable, and offer respective Shore A hardness ranges of 40-70 and 45-75. Both thermoplastic elastomer (TPE) bondable grades, designated as change controlled compounds, are formulated to bond with ABS, PC, PC alloys, PBT, rigid TPU, or co-polyester substrates using...

Read More »
Ceramic Compound is suited for high-temperature heaters.
Repair Compounds

Ceramic Compound is suited for high-temperature heaters.

Provided in powder form and mixed in ratio of 100 parts powder to 18-20 parts water, Ceramacast(TM) 645N fused silica-based ceramic compound can be used to encapsulate small ceramic and metal housings used in devices such as heaters, flowmeters, and pressure and temperature sensors to 3,000°F. Material bonds to ceramics and metals and exhibits minimal thermal conductivity, dielectric...

Read More »
High Temperature Sealer repairs metal components.
Repair Compounds

High Temperature Sealer repairs metal components.

Consisting of ceramic and iron oxide filled paste, Pyro-Putty® 2500 bonds, seals, and repairs defects up to ¼ in. in cross-section in cast iron and steel components up to 1,600°F. Single part, water-based, black-pigmented paste will not decompose at high temperatures and contains no VOCs. Setting at room temperature and curing in-situ or by heating to 200°F for 2-4 hr, product is...

Read More »

All Topics