Temperature Regulator needs no gaskets.
Miscellaneous Regulators

Temperature Regulator needs no gaskets.

Mark 80 uses sealed actuator with stainless steel diaphragm, and does not require bellows. To seal actuator, upper and lower casings and diaphragm are heli-arc welded around circumference to create solid bond, eliminating need for gasket. All sealing surfaces are metal to metal. Sealed, short stroke actuator reacts to smaller temperature changes and needs less time to travel to compensate for...

Read More »
Low-Dropout Regulator powers processor cores.
Electrical Regulators

Low-Dropout Regulator powers processor cores.

MIC49150 1.5 A dual supply LDO is capable of output voltages down to 0.9 V and responds instantly to any abrupt change in load current. It supports input voltage as low as 1.4 V and features thermal shutdown, current limit protection, and ability to use ceramic output capacitors. Transient response is 10 MHz GBW and dropout is 500 mV at 1.5 A. Regulator is available in MSOP-8 and S-Pak packages....

Read More »
LDO Regulator provides standby power.
Electrical Regulators

LDO Regulator provides standby power.

Low dropout regulator, in IttyBitty(TM) SOT-23-5 package, suits applications in portable and fixed systems and consume only 18 microA of quiescent current. Model MIC5233, with input voltage range of 2.3 to 36 V, supplies up to 100 mA of output current. Model MIC5235, with input voltage range of 2.3 to 24 V, supplies 150 mA. Applications include keep-alive circuits in battery or telecom systems,...

Read More »
Electrical Regulators

Integrated Circuits have ultra-low dropout of 500 mV.

Low-dropout regulator (LDO) ICs are manufactured in S-Pak packaging. MIC3730X LDOs provide 1.5, 1.8, or 2.5 V at 3 A from minimum supply of 2.25 or 3.0 V. Model MIC37300 has 3 terminals, MIC37301 includes fault condition error flag and enable pin for on/off control. MIC37302 offers adjustable output voltage as well as output voltage on/off control. All devices are microCap designs, which permits...

Read More »
Pneumatic Fittings simplify motion control.
Miscellaneous Regulators

Pneumatic Fittings simplify motion control.

Blocking fittings mount on air cylinder port and use independent pilot air signal to block movement of piston rod at selected positions. Slow Start fittings control speed at which cylinders recover position. Flow Control Regulators are unidirectional and adjust speed of cylinder rod by controlling inlet or outlet flow. Inline Flow Controls mount anywhere and can be ganged together. Right Angle...

Read More »
Switching Regulators provide small footprint.
Electrical Regulators

Switching Regulators provide small footprint.

S-835X Series of PWM and PWM/PFM CMOS switching regulators consist of reference voltage source, oscillation circuit, error amplifier, phase compensation circuit, PWM control Circuit (S-8355/57) and PVWM/FM switching control circuit (S-8356/58). Oscillation frequencies of 100, 250, and 300 kHz are available. Regulators have low operation current consumption of 25.9 microA (3.3 V, 100 kHz). SNB6B...

Read More »
Static Voltage Regulator monitors for source voltage sags.
Electrical Regulators

Static Voltage Regulator monitors for source voltage sags.

STARSINE(TM) Medium Voltage Static Voltage Regulator (MV-SVR) provides compensation for utility sag events within 1/4 to 1/2 cycle of detection. System is capable of boosting load voltages from as low as 55% of nominal to above 90%. Offered with ratings from 100-1200A with system voltages of 3.3kV to 34.5kV at 50/60Hz, MV-SVR operates with 99.3% rated efficiency. Unit requires no environmentally...

Read More »
Low Dropout Regulator is available in S-Pak package.
Electrical Regulators

Low Dropout Regulator is available in S-Pak package.

MIC37150/1/2 1.5A LDO is designed for powering 1.5, 1.8, or 2.5 V from minimum supply of 2.25 or 3.0 V. It features dropout of 500mV over all conditions. MIC37150 is a 3-terminal device; MIC37151 includes error flag to warn of fault condition and enable pin for on/off control; and MIC37152 offers adjustable output voltage as well as on/off control of output voltage. uCap design allows use with...

Read More »
FRL Units are constructed of stainless steel.
Pressure Regulators

FRL Units are constructed of stainless steel.

Prep-Air® II units include filters, coalescing filters, regulators, piggybacks and lubricators. They are available in 2 basic body sizes: 3/8 in. body with 1/2 in. ports and miniature 1/8 in. body with 1/4 in. ports, with either NPT or BSPP threads. Individual units can be piped together using stainless steel pipe nipples. All units meet NACE specifications.

Read More »

All Topics