Pallet Rack System meets almost any size/capacity requirement.
Material Handling and Storage Racks

Pallet Rack System meets almost any size/capacity requirement.

Selective pallet rack system provides years of continuous service in rugged environments. Upright frames are 50,000 psi steel with one-piece welded construction. Beams are of continuously welded tubular construction, each with 3 or more heavy-duty load bearing studs. They are designed to snap and lock securely to frame in one step. Replaceable spring safety locks prevent accidental beam...

Read More »
Full Extension Shelves slide on cantilevered monorail.
Racks

Full Extension Shelves slide on cantilevered monorail.

Monorail attached to top of unit reduces risk of back injuries caused by maneuvering heavy items such as engines, molds, dies, fixtures, and spare parts. Units require less floor space and eliminate 2 or 3 steps in material handling since operator can roll out shelf, pick up needed item with overhead hoist, and move it directly to work area.

Read More »
Racks and Cabinets accommodate network equipment.
Storage Cabinets

Racks and Cabinets accommodate network equipment.

EIA 310-D industry standard, 19 in. wall-mount racks and cabinets include 5 models in 18 different configurations. Hinged wall-mount panels, available in 1, 2, 4, 6, or 8 rack units accommodate partial network installations or remote nodes, while fixed wall-mount racks in 12, 20, 25, and 32 rack units are suitable for banks of small networking equipment. Racks and cabinets are constructed of 12...

Read More »
Storage Rack offers seamless, square-tube construction.
Material Handling and Storage Racks

Storage Rack offers seamless, square-tube construction.

Raptor-Rak has 3 in. wide upright columns that withstand heavy-volume forklift traffic. Fully welded tubular beams connect via 3 or 4 stud end connectors, with spring-steel, replaceable safety locks. Frame posts come in 14 through 11 gauge, 50,000 psi continuously welded steel. Hot-rolled steel makes up horizontal and diagonal angle bracing, which is MIG-welded to posts. Raptor-Rak uprights...

Read More »
Rack System provides mobile pallet storage.
Material Handling and Storage Racks

Rack System provides mobile pallet storage.

PushBack Rack System is based on the use of overriding, wheeled pallet carts that travel on slightly canted rails, allowing carts to roll forward to front of bay. System configurations range from 2 to 6 pallet positions deep, with variable bay widths to accommodate single-wide or double-wide pallet rows. Upright frame is 1-piece construction, made from 50,000 psi steel, with horizontal and...

Read More »
Shelves and Shelving

Rack holds up to 1,600 lbs per shelf.

Rivet-Grip(TM) freestanding heavy-duty rack is stocked 7 ft high, with depths from 12 to 48 in. and widths from 36 to 96 in. For long rows, it uses common uprights to reduce cost and enhance rigidity. Capacities range from 350 to 1,600 lb per shelf, which are available with particleboard or wire inserts.

Read More »
Racks store empty pallets.
Material Handling and Storage Racks

Racks store empty pallets.

Single-Leg Over-Dock Storage Racks feature upright frame with offset leg, and one single back column up to height that will clear door. Ceiling Supported design must be worked into building plans to ensure structural stability. It has no lower legs to interfere with traffic. Racks include structural channel load beams with bolted connections. Two bolt-in pallet supports are installed under each...

Read More »
Purge Cabinet offers roll-out shelves.
Racks

Purge Cabinet offers roll-out shelves.

Nitrogen Purge Cabinet features sealed sides, back, and doors that can be made of plexiglass when visual control is required. Roll-out shelves provide easy access to all items being stored. Shelf sizes range up to 10 ft wide and 5 ft deep. Units can also be made completely out of stainless steel.

Read More »
Cantilever Rack features all structural-steel components.
Material Handling and Storage Racks

Cantilever Rack features all structural-steel components.

Cant-I-Beam System with I-Beam construction is designed for medium- to heavy-duty load service. Both columns and arms are made of structural I-beam sections, with arms fastened to columns by 4 bolts. Arms are adjustable on 4 in. centers. Base assemblies also bolt to column, with 1 required for single-side storage; 2 for double-side storage. Load capacities range up to 109,000 lbs per column and...

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers