Pushbutton Switches feature silent actuation.
Available in 12, 15, and 17.4 mm cap sizes, Series KP01 Switches measure only 23 mm from PC board to top of cap and feature 4.5 mm travel. They provide positive indication of circuit transfer as well as smooth operation. Rated at 100 mA max at 12 Vdc, SPST momentary switches include built-in, red/green bicolor LED. Snap-in standoff provides secure board mounting and alignment. Epoxy-sealed...
Read More »
Lens is available for lighted pushbutton switches.
Interchangeable lens for company's SW44002 series switches can be read in on/off conditions. Sunlight-readable lens measures 0.520 in. sq., 0.465 in. deep to rear lens edge, and can be installed directly onto switches from mounted or rear-mounted installations. Lighting brightness averages 250 ft-l minimum. Chromacity is aviation yellow. Mil-Spec lens suits installation in aircraft and avionics...
Read More »
Miniature Pushbuttons come in 1-, 2- and 4-pole versions.
Offered with momentary and alternate circuits, MB2000 series pushbuttons are available in single-, double-, and 4-pole, double throw configurations. They feature over-center actuator mechanism, guide-interlocked actuator blocks, frames clinched above case, and epoxy-sealed terminals. Power rated models are 6A @ 125 Vac and 3A @ 250 Vac or 3A @ 30 Vdc. Logic level devices are rated at 0.4 VA max @...
Read More »
Emergency Stop Boxes offer 300,000 operation life-span.
Made of shock-proof technopolymer with double insulation, Series CC features EN 418 compliant, mushroom head pushbutton and double break, positive opening NC contacts. One bottom and two side conduit entry knockouts allow for installation in any orientation. Boxes carry IP 65 protection rating and will operate from -25 to +70Ã-
Read More »
6 Engineering & High-Performance Plastics Used for Machined Components
This resource breaks down six of the most commonly used high-performance plastics, properties and common applications, and questions to ask during material selection.
Read More »
Switches combine illumination with tactile switching.
Rated for 50 mA loads at 48 Vdc, Series JS features 12 mm switches with red, green, yellow, or blue LEDs. Typical applications include audio/video equipment, consumer electronics, and test instruments.
Read More »
Pushbutton Switches come in lit or non-lit versions.
Illuminated and non-illuminated UB series switches have behind-panel depth of .394 in; square models have .628 in.Ã-² panel cutout, while rectangular devices have .638 x .882 in. cutout. Rated 5A @ 125/250 Vac or 5A @ 30 Vdc for power rated models and 0.4 VA max @ 28 V AC/DC max for logic level devices, switches have mechanical life of one million operations min for momentary models and...
Read More »Pushbutton Switch handles manufacturing applications.
Equipped with plastic and metal operator components, Bulletin 800F series employs flexible, constant energy design that incorporates interchangeable components and allows one-person mounting. Available back-of-panel components, designed to fit space and application requirements, include latch, contact block, and LED. Series provides protection and corrosion resistance for IP65/66 and Type 4/4X/13...
Read More »Off-On Latching Pushbutton Switches suit harsh environments.
Available with solder lug or insulated wire lead terminals, IP Series pushbutton switches provide visual indication of switch state with 2-position actuator. Switches mount in 13.6 mm hole and project behind front panel less than 20 mm. They feature shock and vibration resistance, round and square panel bezels, and illumination options. Their IP67 seal is accomplished via internal elastomeric...
Read More »
Pushbutton Switches measure only 7 x 7 x 2.5 mm.
Constructed of glass fiber-reinforced polyamide, Series GB2 switches feature STC contact mechanism, which provides logic-level switching reliability and positive, smooth detent actuation. STC contacts self-clean with each actuation, and off-center plunger design ensures against accidental actuation. Pushbuttons are momentary circuit and SPST with OFF-momentary ON configuration. Rated at 0.4 VA...
Read More »
Pushbutton Switches offer dual and quad displays.
Series 644-2100 Multi-Function/Multi-Image Lighted Pushbutton Switches can be singly used in place of up to 4 individual switches. Units are capable of display configurations in split, quadrant or full segments, and can provide both continuous visible legends and hidden legends that become visible when switch functions are activated. They accept T-1 sub-midget flange-based lamps and LEDs. Switch...
Read More »
Dodge® Raptor Coupling Now Available in Three Larger Sizes
The Dodge Raptor coupling epitomizes the innovation and value that has made Baldor a world leader in industrial electric motors. For almost 100 years Baldor has been the go-to source for industries across the globe. The Raptor coupling is just one example of our dedication to engineered excellence and commitment to providing value and performance. See our video to learn more.
Read More »
