Dispense System varies flow rate, shot size and mix ratio.
Pumps

Dispense System varies flow rate, shot size and mix ratio.

Program-A-Shot 997 dispenses 2-component silicone, epoxy or urethane for potting or encapsulation applications. Flow rate, shot size and ratio can be electronically adjusted to mix and match parts on same production line without reprogramming system. For example, bar-code reader could identify part, then direct system to use programmed profile that dispenses material at pre-determined volume, mix...

Read More »
Underwater Pumps run in air or can be submerged.
Pumps

Underwater Pumps run in air or can be submerged.

Model 893-09 or -10 pump has brushless 12 or 24 Vdc motor that can run in open air or fully submerged in water. Pump and motor are rated at 50,000 hr life, and produce 3 gpm at 1 ft head or 10.5 ft head at 0 flow. Pump comes with 3/8 in. OD smooth outlet and 3/8 in. female pipe thread inlet. Other size inlets and outlets for hose and threaded connections are available. Standard plastic components...

Read More »
Gear Pump Gears are available in herringbone style.
Gear Pumps

Gear Pump Gears are available in herringbone style.

Optional herringbone gears are available for extrusion, compounding, polymer extraction and transfer pumps. Gears increase discharge pressures, extend life of pump's parts, and provide equal bearing loading that reduces energy requirements, decreases temperature and shear to fluid, and decreases pulsations from gear pump. Applications include compounding, tape production, pipe production, polymer...

Read More »
Tiny Pumps dispense small amounts.
Pumps

Tiny Pumps dispense small amounts.

SV700 Series of inert, solenoid-operated micro pumps are suitable for dispensing re-agents, dilutants and lubricants. Pumps are less than 3 in. high, have diameter of 1.10 in., and dispense volume of 50-250 Â-µL. Available with glass-filled polypropylene pump head and EPDM or viton elastomers, pumps are compatibile with wide range of fluids. Fluid connections include 1/4-28 flat bottom...

Read More »
Considerations for Choosing a Plastic Injection Molder
Sponsored

Considerations for Choosing a Plastic Injection Molder

Choosing a plastic injection molder is no small decision. There are a number of factors that play into your selection, and it's important to consider them all to ensure you find the plastic injection molding company that suits your unique needs. This eBook is your guide to identifying those factors to help you make an informed decision.

Read More »
Drum Pump has no moving parts.
Pumps

Drum Pump has no moving parts.

Dual-Force Vac dual mode (fill/empty) drum pump is driven by filtered compressed air and Transvector air amplifier. It is capable of filling 55-gallon drum in less than 2 minutes. Pump features fast-turn switch that changes from vacuum to pump mode, automatic safety shutoff valve to prevent overflows, and relief valve that limits internal drum pressure to 8 PSIG. Unit is resistant to most...

Read More »
Submersible Pumps do not require cleaning.
Pumps

Submersible Pumps do not require cleaning.

N-Pumps employ open-type self-cleaning impeller, and while operating, each leading edge passes across sharp stationary relief-groove. This action ensures that rags, stringy materials and solids are sheared, cleaned from impeller and pumped away. Pumps maintain high level of efficiency, even in fluids with high solids and fibrous content.

Read More »
Metering Pumps feature corrosion resistance.
Pumps

Metering Pumps feature corrosion resistance.

MD Metering Pumps are available with rotating parts in 316 stainless steel, Hastelloy® C4, titanium or Kynar® and casings in HDPE, 316 stainless steel, or Halar®-coated stainless steel. Mechanical seals are available with various metallurgies; PTFE lip seal can also be used. Pumps handle thin liquids and materials to 100,000 cps. They do not require pulsation dampeners or...

Read More »
Pump Head handles 2 channels at once.
Pumps

Pump Head handles 2 channels at once.

Masterflex Easy-Load II pump head can pump 2 channels simultaneously, eliminating need for stacking pump heads. Flow range is 0.06 to 1000 mLpm per channel depending on drive rpm and tubing selection. Each pump head accepts L/S 13, L/SC 14, L/S 16 and L/S 25 tubing sizes in any formulation. Available with cold-rolled steel or stainless steel rotors, pump head is also suitable for applications...

Read More »
Diaphragm Pump primes itself to 23 ft wc.
Diaphragm Pumps

Diaphragm Pump primes itself to 23 ft wc.

Air-operated Tapflo Aluminum Series double diaphragm pumps are suited for wide range of media, including paint and coatings, waste plant chemical dosing and many other pH-neutral liquid pumping applications. Pumps are available in 5 sizes covering flow capacities up to 110 gpm with infinitely variable flow control and dry run capability. Pumps handle wide range of fluid viscosities as well as...

Read More »
Oil Pump fits into drums and tanks.
Pumps

Oil Pump fits into drums and tanks.

Model 1737 1:1 ratio stub-style oil pump works with oils and non-corrosive liquids in industrial, manufacturing and automotive service shops. Pump fits drums and tanks with a 2 in. bung opening. It has maximum air pressure of 145 psi, working pressure of 100 psi, and self-lubricating pressure relief port. It comes with connecting hoses and an air line filter. Pump weighs 6 lb.

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers