Centrifugal Pumps feature double cartridge seals.

Centrifugal Pumps feature double cartridge seals.

Suited for corrosive and abrasive materials, Series 1700 Seals on Stan-Cor Centrifugal Pumps are hydraulically-balanced and feature cassette-within-a-cartridge design. Removable inner cassette allows gland to be reused with each new seal. Friction drive lock ring with cap screw assures alignment and eliminates slippage to facilitate installation. Self-centering locators are internal to seal and...

Read More »
Diaphragm Pump offers stall-free air valve technology.

Diaphragm Pump offers stall-free air valve technology.

Capable of flows to 60 gpm, ARO-® EXP Model PW10A-X-X is constructed of aluminum with 1-½ in. fluid inlet and 1-¼ in. fluid outlet. It offers 5 diaphragm/ball-check options. Air valve design features 4 working parts and solves problem of air-motor stalling. Configuration of valve facilitates access, inspection, and scheduled service.

Read More »
Centrifugal Pump meets high pressures at low speeds.

Centrifugal Pump meets high pressures at low speeds.

Vertical Multi-Stage Series MS5-4x4-SEL-CDM-ADP has flow rates up to 500 gal and is capable of heads up to 700 ft at 1,750 rpm. Available in stainless steel, pump features one-piece shaft, depths to 20 ft, and no seals. It offers extra stages for higher pressures. Applications include industrial washers, filtration systems, chemical plants, power plants, machine tools, spray booths, and phosphate...

Read More »
Pump utilizes Diaphragm Position Control technology.

Pump utilizes Diaphragm Position Control technology.

Series H/G25 Kel-Cell-® uses DPC technology to control diaphragm position under adverse inlet conditions. This reduces possibility of incidental diaphragm failure/rupture caused by conditions that result in excessive vacuum conditions on pump inlet. Industrial pump provides flow to 20 gpm and pressure to 1,000 psi.

Read More »
Close-Coupled Pumps transfer high-solids content materials.

Close-Coupled Pumps transfer high-solids content materials.

Offering flow rates to 1,000 gpm, Moyno-® 2000 CC Pumps feature sealed, Ultra-Drive-® gear-type universal joint drive train and rotor/stator pumping element geometry. ANSI flat face flanges are provided on suction and discharge ends. Single mechanical seals meet DIN Standard 24960 and ISO 3069. Pumps are suited for scum and grease pumping, lime slurry transfer and dosing, chemical metering and...

Read More »
Centrifugal Pumps eliminate clogging problems.

Centrifugal Pumps eliminate clogging problems.

Suited for sludge and slurries containing large solids, entrained air, and fibrous/stringy material, Whirlflo-® vortex pumps feature fully recessed impellers that produce clear flow path to pump discharge. Spherical solids up to 10 in. can pass through pumps. Available in cast iron, high chromium iron, and stainless steel, Whirlflo units range from 2-10 in. with capacities to 7,000 gpm and heads...

Read More »
Metering Pump offers sub-microliter dispensing.

Metering Pump offers sub-microliter dispensing.

Utilizing CeramPump-® valveless piston pumping principle, Model SMTRH provides ultra-low volume, sub-microliter dispensing. Pump is driven by precision stepper motor and will dispense from 500 nL to 5 -µL. Piston stroke displacement is adjusted using flow control ring graduated in 450 divisions. Low dead volume pump head design ensures maximum bubble clearing and provides typical stroke to...

Read More »
Peristaltic Pump features direct-coupled design.

Peristaltic Pump features direct-coupled design.

Available 25-100 mm sizes, SPX32 can pump harsh materials and will not vapor lock. Unaffected by abrasive nature of sludge, corrosive acids, and gaseous chemicals, unit incorporates leak zone that protects drive and self-loading design that facilitates hose changing operations. Design allows for drive removal and replacement without dismantling pump head, and 2-bearing rotor absorbs forces...

Read More »
Peristaltic Pump is used in ferric sulfate treatment.

Peristaltic Pump is used in ferric sulfate treatment.

Used for metering ferric chloride into raw water, 624 U/RE wastewater treatment solution offers vacuum lift, dry priming capability with no possibility of back-flow. Design utilizes twin rollers, providing flow rates from 0.05-12.0 Lpm. Pump accommodates fluctuations in water demand and offers manual speed control, remote switching options, and digital speed display. IP55 rating ensures unit is...

Read More »

Air Flow Pump suits stationary and mobile applications.

Series 6000 Linear Pump incorporates low-voltage dc motor that makes it suitable for medical, environmental, laboratory, office machine, and other stationary and mobile applications. Pump provides up to 1.5 cfm air flow as standard. Maximum pressure is rated at 4.0 psi continuous or 4.7 psi intermittent. Maximum vacuum rating is 8 in. Hg. Intake heads, constructed of high density sound-absorbing...

Read More »
Fresh Air Intake Designed to Meet ASHRAE 62.2 standards
Sponsored

Fresh Air Intake Designed to Meet ASHRAE 62.2 standards

Alan Manufacturing has a long history of developing innovative solutions for HVAC applications. With over 1,000 product designs under our belt, we have gained a reputation as the go-to source for HVAC dampers, hardware, duct supports, zone control systems, and much more. Adding to this extensive list of achievements we now announce the release of our new line of Fresh Air Intake products. Designed to meet ASHRAE 62.2 standards, they are the most robust and high-performance product of their kind. See our video to learn more.

Read More »

All Topics