Armstrong Introduces IPS 4000 Controller with Parallel Sensorless Pump Staging Technology
Designed for commercial HVAC pumping stations of up to 8 pumps and 16 zones. Offers sequences for variable-primary, secondary or tertiary pumping system applications. Compatible with existing building automation systems and pre-programmed for easy installation and set-up.
Read More »
Latest LMI LIQUITRON 7000 Series Controller Offers Multi-Parameter Monitoring and Control
The LMI LIQUITRON 7000 Series Controller comes with 17.8 cm full-color touchscreen and an intuitive user interface. The unit is equipped with an embedded 4G/LTE cellular modem and is embedded with software and wireless connectivity that provides remote monitoring and controls with notifications, alerts and reports. The controller is designed for metering pumps in boiler feed, cooling tower,...
Read More »
New Revelation Pump-Off Controller Provides Data via Supervisory Control and Data Acquisition
The Revelation Pump-Off Controller analyzes the information collected and runs diagnostic by utilizing pump cards, a graphical representation of the pump loads. The unit offers down-hole pump, surface cards, trend data of pump fillage, rod load and polished rod horsepower. It streamlines pump-off set points from specific load and stroke points or based on pump fillage and is suitable for use in...
Read More »
SC100 Pump Controller features a 4-digit, 7-segment digital display.
SC100 Pump Controller features push buttons helps to simulate the level, scroll through the parameters, and to change the parameter settings. Unit offers scaling range of 4-20 mA level input signals. Controller comes with pump up/pump down, lag delay and forcing the lead pump position features.
Read More »
How to Select a Rubber Compounding & Mixing Supplier
To learn more about rubber compounding and mixing, and how experienced manufacturers like AirBoss can meet your needs, download this whitepaper now.
Read More »
Stormcell 442 Series Pump System offers remote monitoring.
Featuring professional-grade charger, Stormcell™ 442 Series Pump System provides 12 volts battery backup. Designed in 10 and 25 amp models, unit provides remote monitoring using NightEye™ app wireless technology. Device is energy efficient for longer run-times.
Read More »Variable Speed Control eliminates complex programming at pump.
Available for Apex condensing boilers, Eco Propel Cognitive Pump Control integrates boiler firing rate with pump speeds to optimize efficiency while minimizing electrical consumption. A 0–10 V signal is communicated to pump to ensure desired flow and delta T is returned across all firing ranges. By reducing pump speeds as much as 85% under single-speed pumps, Eco Propel eliminates wasteful...
Read More »Cognitive Pump Control optimizes boiler efficiency.
Pre-engineered and fully tested, variable speed Eco Propel integrates boiler firing rate with pump speeds, optimizing boiler and system efficiency while reducing electrical consumption. Demand is calculated based on supply temperature and return temperature, and boiler firing rate is determined from outdoor air sensor, header sensor, or set-point. To harmonize operation, 0-10 V signal is...
Read More »
Touchscreen Pump Controller features built-in programming.
Providing motor speed control for Hydra-Cell® pumps, Control Freak™ allows user to enter desired flow rate or volume in gallons or liters and system pressure in psi or bar. Controller then automatically runs pump manually at desired flow rate or volume total/time, or in pre-set batches. Featuring variable frequency drive, unit can control up to 6 pumps with 1 screen and 10 separate batch...
Read More »Irrigation System Controller helps farmers optimize water use.
Allowing farmers to applyÂ- consistent amount of water on area covered by center-pivot corner arm, Irrigate-IQ™ uniform corner prevents over- and under-watering through uniform application. Algorithms enable consistent water application regardless of position of corner arm. To minimize risk of application overlaps or gaps, solution controls each individual nozzle...
Read More »Remote Irrigation Controller enables creation of no spray areas.
Irrigate-IQ™ optimal flow lets growersÂ- with standard irrigation pump equipment (without variable frequency drive pump) incorporate no spray areas within their irrigation plan to concentrate irrigation efforts in highest-producing field portions. Standard pump equipment is utilized to keep water pressure regulated across entire pivot, even when operating in no spray areas, and...
Read More »
More performance and functionality for Sinumerik 828D CNC
Siemens new SINUMERIK 828D ADVANCED, SINUMERIK 828D and SINUMERIK 828D BASIC sets the standard for productivity enhancements of turning and milling operations on standardized machines and simplify the automation of grinding machines. See our video to learn all about it.
Read More »
