Pressure Regulators

Natural Gas Pressure Reducing Regulator has high-flow design.
Pressure Regulators

Natural Gas Pressure Reducing Regulator has high-flow design.

By helping maintain consistent inlet pressures to downstream equipment, Type T99 regulatorÂ- allows accurate control of distribution system pressures. This applies even in applications with widely varying flow rates and supply pressures as well as high inlet pressure and low flow control applications. Tight shutoff is provided by heavy main spring working through lever to provide seat...

Read More »
Stainless Steel Pressure Regulators handle corrosive media.
Pressure Regulators

Stainless Steel Pressure Regulators handle corrosive media.

Available in 3 spring ranges, direct-operating BelGAS Type P95H enables in-line maintenance and is suitable for air, steam, process gases, corrosive liquids, oil and gas. Type P98H, consisting of back pressure regulator and relief valve, monitors upstream pressure and opens to relieve excess pressure increases above set point. Type P627 spring loaded, direct-operated, low and high gas pressure...

Read More »
Back Pressure Regulator has blockage-resistant design.
Pressure Regulators

Back Pressure Regulator has blockage-resistant design.

Available in pressure ranges up to 5,000 psi (standard trim) and 10,000 psi (high-pressure trim), BR series does not require heating to maintain pressure control. All-mechanical design eliminates ability of oil and ice to cling to internal passages of regulator, and control valve is pilot operated. Pilot pressure can be controlled usingÂ- manually operated knob adjusted pressure regulator or...

Read More »
Back Pressure Regulators act as drop-in Mity Mite replacements.
Pressure Regulators

Back Pressure Regulators act as drop-in Mity Mite replacements.

Drop-in replacement regulators are available for models of Mity Mite back pressure regulators, which are suited for applications in oil and gas industry due to materials of construction and low flow capabilities but are no longer commercially available. Replacements for several models of Mity Mite back pressure regulators follow same part number scheme with EQ appended to end.

Read More »
PTFE Regulator can withstand high pressures.
Pressure Regulators

PTFE Regulator can withstand high pressures.

Designed to use a flexible, frictionless diaphragm as the only moving part, Equilibar back pressure regulators are able to accurately maintain pressure over a wide range of flow rates, including high flow rates. Now this novel design is available for applications requiring PTFE (Teflon) wetted parts. The machined TeflonÂ-© body can use 1/8″ and 1/16″ PTFE tubing and is rated to 250 psig...

Read More »
Back Pressure Regulator withstands aggressive chemicals.
Pressure Regulators

Back Pressure Regulator withstands aggressive chemicals.

Available with Â-½–2 in. port sizes, Equilibar© Back Pressure Regulator utilizes flexible diaphragm as only moving part. Body is CNC-machined from PVDF bar stock, while diaphragm is manufactured from glass matrix reinforced PTFE material. Diaphragm acts to directly seal against valve seat, eliminating need for friction-causing dynamic seals. With response time measured in...

Read More »
Pressure Regulators

Miniature Pressure Regulators come in multiple configurations.

MAR-1 Series includes relieving designs, whichÂ- maintain constant pressure output even when downstream conditions change, as well as non-relieving designs, which do not automatically compensate for changes in downstream flow or pressure. Supporting flows to 5 scfm, series does not vent to atmosphere. Output pressure can increase due to downstream event,...

Read More »
Pressure Regulators

Gas Regulator is intended for commercial service applications.

Used to supply natural gas to commercial applications, Fisher® Commercial Service Regulator model CS804 has integral slam-shut that lends to extended service life and facilitated maintenance. DesignÂ- eliminates false trips due to inaccurate internal registration, vibration, high flow rates, and/or cold temperatures. Also, internal registration eliminates need to...

Read More »
Control Valves vs. Regulators in Control Applications
Pressure Regulators

Control Valves vs. Regulators in Control Applications

Understanding the differences between regulators and control valves is crucial in the automation industry. Each of these holds equal importance but have different functions and also operate in a different way. It is important to be knowledgeable about both solutions so that control process designers do not engage in major problems or waste money and resources. Understanding the Difference First,...

Read More »
Pressure Regulators

Pressure Reducing Regulator is designed for gaseous applications.

Offered in Â-½ and ¾ in. Tri-Clamp® body connections, PA1 has self-draining body design and trims that comply with ASME BPE 2012 SF-4. All wetted, metal parts are constructed of 316L stainless steel. Capable of withstanding inlet pressures up to 250 psig and outlet pressures up to 135 psig, regulator also has EPDM diaphragm and also comes with option of...

Read More »

All Topics