Custom Drive Belts provide abrasion resistance.
Manufactured to metric or inch requirements, PYRATHANE 88A Drive Belts are made of polyester-based polyurethane with Shore hardness of 88A. Round belts can be custom made with cross sectional diameters from .062-.562 in., while flat belts range from .030-.187 in. in thickness and in widths up to 1.500 in., both with no max length restriction. PYRATHANE belts provide quiet operation in small parts...
Read More »
Flat Belts feature endless design with no welds.
Available with or without carcass reinforcement, HytrelÃ-® Flat Belts are flexible at temperatures as low as -40Ã-
Read More »Modular Plastic Belt suits glass container handling.
HabasitLINKÃ-® M2620 Flat Top Heavy 1 in. modular belt is 0.5 in. thick and meets industry criteria by offering abrasion resistance to broken glass particles. Belt is complimented by heavy-duty sprocket with duplex of drive teeth. Applications include palletizers/depalletizers, accumulation conveyors, mass handling lines, and case packing.
Read More »
Transmission Belt reduces downtime for RPP drives.
Eliminator(TM) belt, engineered to replace RPPÃ-® tooth profile belts of same width and comparable length, run on existing RPP sprockets and idlers with same tension as original belt. Polyurethane synchronous belts with green tooth color are available in 8 mm pitch size with 12, 22, 35, and 60 mm widths; 26 belt lengths; and 104 part numbers, or 14 mm pitch size with 20, 42, 65, 90, and 120...
Read More »
An Introduction to Purchasing Castings
To learn how Liberty Cast Products can guide you through your sand casting project, download now.
Read More »
Conveyor Belt facilitates cleaning.
Small-pitch Series 1100 Flat Top Belt, for use with EZ Track sprockets, features underside design that incorporates continuous cross section so sprockets can be placed anywhere across width of belt. Sprockets contact belt underside at hinge and link areas to drive and track belt securely, eliminating risk of disengagement. Design of underside eliminates potential debris traps otherwise created by...
Read More »
V-Belts suit various conveying applications.
Integral Supergrip Surface V-belts incorporate co-extruded design that eliminates delamination of supergrip surface from thermoplastic V-belt. With co-extruded NSW design, belts are available in polyurethane and polyester constructions with non-reinforced and polyester reinforced options. Abrasion resistant products install with on-site, butt-welded splicing. Belts are offered in full rolls or...
Read More »
Timing Belt has teeth on both sides.
Suited for serpentine applications, NSW polyurethane timing belt offers timing-teeth on both sides. Double-Sided belt is built with continuous wound steel reinforcement and responds well to stress. Resistant to abrasion and flex fatigue, NSW belt also resists moisture, grease, oil, and gasoline, as well as ultraviolet light, ozone, and hydrolysis.
Read More »
Drive Belt provides extended wear.
Drive belt cuts required belt changes in half and is used on line-shaft roller conveyors made by Hytrol, Ermanco, Bushman, Rapistan, and Matthews. It is constructed from 45D Shore Hardness, polyester-based polyurethane with internal lubricant package.
Read More »
Drive Belts handle loads with reduced drive widths.
WhiteHawk Pd and BlackHawk Pd positive-drive, synchronous belts increase load-carrying capacity and allow narrower belt-drives. Oil-resistant, cross-linked elastomer Hibrex rubber compound is formulated to increase tooth rigidity. WhiteHawk 8 mm and 14 mm pitch belts are available in 20 mm to 170 mm widths and 480 mm to 6.86 meter lengths. BlackHawk 8 mm and 14 mm pitch belts are available in 12...
Read More »
Ensure Safety, Reliability in Your Cement Plant with Aerzen Blowers and Compressors
Aerzen offers blowers and compressors for challenging cement applications such as pneumatic conveying from raw mill to raw meal silos, combustion air, cement silos fluidization, and more. At Aerzen, safety is our top priority. Check out our video to learn more.
Read More »
