New Power Supplies Products

DC Source offers multi-channel programmable operation.

GX1838 3U PXI DC source provides 8 output channels and 3 programmable 14-bit voltage rails. Each voltage rail can be programmed to output between -9 and +32 V, and can provide current of 100 mA. Rails can also be connected to external input, and Rail C can be connected to on-board programmable electronic load. Each rail may be switched to any of 8 output channels.

Power Supply works in harsh environments.

Ruggedized Model 1.10.750 has operating temperature range of -25 to +50Ã-

DC-DC Converter provides up to 70A in half brick package.

PAH200H series DC-DC converter offers power density of over 105 W/inÃ-³, and provides three output voltage choices from 1.8 to 3.3 V. Efficiencies are rated up to 90% for 3.3V output unit. Unit operates from nominal 48 V input, provides regulated output at power levels up to 198 W, and accepts DC inputs from 36 to 75 Vdc with peak of 100 V for 100 ms. Features include remote sense,...

Redundant Power Supply can be hot swapped.

In case of primary power supply failure, RPSS redundant power supply system for company's Series 90(TM) -30 controllers, switches power to backup unit without process interruption. If one power supply fails, user can replace failed unit by removing power from defective unit and hot swapping it while backup unit is powered and controlling process. Module is compatible with all Series 90-30 power...

A Guide to Trade Credit Insurance

This white paper provides a how to guide to trade credit insurance to protect your business from bad debt, optimize credit management, enhance working capital and accelerate growth.

DC/DC Converters deliver 60 Amps output current.

Open frame ALH60 and heat sink adaptable AEH60 are 60 Amp, half-brick converters with efficiencies up to 91% on 3.3 V model and 89% on 1.8 V model. Units include over temperature, over current and over voltage protection, plus under voltage lockout with hysteresis to prevent false starting and stopping at low input voltages. With 36 to 75 V input range and output voltages of 1.2, 1.8, 2.5, and...

DC to DC Converter measures 1.45 x 2.3 x 0.43 in.

DualQor(TM) series dual output voltage, quarter-brick sized isolated dc/dc converter delivers up to 60 W total output power at Ã-

High-Density Power Supply can be configured to specification.

Switch-mode, AC-DC Vega Series is offered in 450 and 650 W models with 10 outputs (max) each and no minimum load requirements. It provides seamless output voltage from 1.8 to 62 V, density of 5.8 W/inÃ-³, and allows input from 85 to 264 Vac. Modular series offers single PCB design, in both front-end converter and output module stages, and provides over-voltage and over-current protection.

Adapter offers up to 38 W of power.

PSA45U-201 adapter switching power supply provides dual outputs: +5 Vdc for logic control and +12 Vdc for motors, disk drives, tape drives, and external peripherals. It has active overvoltage protection at 6.5 V max. Overcurrent protection offers short circuit auto restart and provides minimum hold-up time of 12 ms at maximum load of 120 Vac. Operating temperature is 0 to 40Ã-

Switching Power Supplies come in small packages.

High density, enclosed MKS75-Series accepts input from 85-265 Vac and 47-440 Hz, provides output power of 75 W, and measures 5 x 3 x 1.7 in. Four models are available that provide single outputs from 5 to 24 Vdc. All operate over ambient temperature range of -10 to +60Ã-

DC-AC Inverter powers automotive LCDs.

Fully encapsulated for resistance to shock, vibration, and humidity, P44W powers LCDs used in GPS systems and audio and video displays in car interiors. It meets starting voltage and current requirements for automotive OEMs, provides up to 15 W of output power, runs at up to 9 mils boost current for quick warm-up in cold starts, and performs over operating temperature range of -86 to +185Ã-

Standex Engraving Mold-Tech Offers Nickel Shell Capabilities on a Global Scale

Standex Engraving Mold-Tech is the premier, global supplier for mold texturing and surface finishing. With a full range of services, Standex Engraving Mold-Tech is also the only nickel shell supplier producing in three global locations. See our video to learn more.