Canvas Tool Bags have multiple pockets and shoulder strap.

Constructed of No. 8 natural canvas, 5002 and 5003 Series canvas tool bags come in 16, 18, or 20 in. lengths with leather or vinyl bottom and 6-stud bottom reinforcement. Models with leather bottom are available with mounts that accommodate padded, adjustable, 2 in. wide shoulder strap made with non-marking, anti-slip material. All bags feature steel frame mouth with hinge, while 20 in. bags have...

Read More »
Trim Saw cuts copper and aluminum tubes.

Trim Saw cuts copper and aluminum tubes.

Model 315 produces repeatable, smooth, parallel cuts that are burr-free and require little or no surface cleaning. Heavy-duty base table and sub-assembly provide structural support, while hydraulically actuated tube clamp anchors various sized tubes that can be cut simultaneously. Hydraulic motor drives blade, and hydraulic cylinder with feed valve feeds blade through tubes. Lubrication and...

Read More »

Woodworking Saw allows 30 in. of ripping capacity.

Contractor's Saw-® line of 10 in. table saws are equipped with miter gage, straight grind table surface, and choice of 3 fence systems for cutting accuracy. All saws operate with a 2-capacitor 1-½ hp, 120/240 V motor and have a see-thru blade guard with splitter and anti-kickback fingers. Miter gage features 9 positive stops, including standard 45-° and 90-° stops, and fence systems all have...

Read More »
Compressors offer pressures as high as 650 psig.

Compressors offer pressures as high as 650 psig.

Suited for PET bottling lines and leak testing, Booster Compressors extend from 3-50 hp with flows from 10-600 scfm. They are equipped with TEFC motor, motor starter, control monitoring system, aftercooler, prefilter, anti-vibration pads, and discharge hose. Units boost existing plant pressure, eliminating need for separate high-pressure systems and complex installation requirements.

Read More »
Signal Conditioners and Electronics support TEDS Sensors.

Signal Conditioners and Electronics support TEDS Sensors.

Rack mountable TEDS (Transducer Electronic Data Sheet) multi-channel and dual-mode signal conditioners are available for use with ICP-® and charge output vibration, pressure, and force sensors. In-Line Charge Converters are available with TEDS capabilities, which enable the devices to store and recall TEDS data for attached sensor. In-Line TEDS Adaptor features interface chip that allows...

Read More »
Cutting Machine cuts tubing, conduit, and wire.

Cutting Machine cuts tubing, conduit, and wire.

SLICE 142 saves waste by allowing user to load 4 ft long, double-wall sticks of heat shrink tubing without cutting off long piece of material. It knows by length of piece to be cut how many pieces it can cut from 4 ft length. After cutting pre-calculated pieces, machine pauses and waits for next stick to be loaded.

Read More »
Heavy-Duty 8-in-1 Tool has multi-purpose blade.

Heavy-Duty 8-in-1 Tool has multi-purpose blade.

Allway BG1 Multi Tool features soft-grip, ergonomic handle over-molded with Santoprene rubber as well as precision-ground, stainless steel blade with chisel edge. Threaded end accepts standard extension poles, while nail-setting hammer-end unscrews to accept threaded extension pole for scraping or spreading jobs. Unit serves as paint scraper, glazier's knife, chisel, putty knife, tile remover,...

Read More »
Vises offer repeatable part clamping solutions.

Vises offer repeatable part clamping solutions.

High Density Long Vise has two 4 in. capacity stations with hard jaws that provide repeatable clamping up to 0.001 in. Manual model delivers up to 6,316 lb clamping force at 70 lb torque, while hydraulic model provides 7,800 lb of force at 5,000 psi. Suited for holding very large parts, Model D810 has 10 in. jaw opening and 11,600 lb clamping force. Available in 4-face and 2-face models,...

Read More »
Hammer Drill is portable and lightweight.

Hammer Drill is portable and lightweight.

Cordless TE 2-A, 24 V Electropneumatic Hammer Drill performs rotary drilling, straight drilling, or setting screws when working on concrete, brick, and masonry. TE 2-A drills anchor holes in concrete from 3/16-3/8 in., and also provides capacity for drilling up to 1 in. holes in wood, 3/8 in. in steel, and up to 5/8 in. in concrete. Compact drill weighs 8.36 lb, and is offered with either 3.0...

Read More »
Walk-Behind Saw cuts concrete and asphalt up to 7 in. deep.

Walk-Behind Saw cuts concrete and asphalt up to 7 in. deep.

Portable, pneumatic Model CSR 150 features 9.5 hp air motor with gearbox that reduces turning speed from 5,250 to 2,900 rpm to regulate blade speed and increase torque to cut hard materials. Crank handle raises and lowers blade for cutting depths up to 7 in. Saw features 1 in. arbor, blade capacity up to 20 in. diameter, solid rubber casters, pointer to follow scribe line, and -¾ in. water...

Read More »

All Topics