Carpet Extractors

The Solus Can Do It Alone

The Solus 500 portable heated carpet extractor from U.S. Products is designed for one-operator carpet cleaning. This CRI Gold-certified machine has a dual, top-mounted, three-stage vacuum system and low-moisture technology, which leaves carpets cleaner, drier, and healthier. Generating 0-500 adjustable psi, the Solus 500 has an on-demand heat system that produces up to 212 degrees (F) heat,...

Read More »
Multi-Bit, Ratcheting Screwdriver combines ergonomics, strength.
Screwdrivers

Multi-Bit, Ratcheting Screwdriver combines ergonomics, strength.

Designed for electricians, 21-n-1 Twist-a-Nut(TM) has 4 most frequently used bits pre-loaded into driver shaft. Additional 12 bits are securely stored for quick access within handle. Dual interchangeable chrome-vanadium shafts are designed for driving Â-¼, 5/16, and 7/16 in. nuts, and handle also has 2 Accu-Loop(TM) wire looping holes along with Wire-Nut® ratcheting wrench formed into...

Read More »
Small Screw Insertion System minimizes repetitive motion injury.
Inserters

Small Screw Insertion System minimizes repetitive motion injury.

With StickShooter(TM) driver, PEM® StickScrew® System accommodates interchangeable nose assemblies and allows for quick tooling changeover. Self-contained system combines air-powered driver with sticks of serially connected hex head screws, enabling automatic screw installation without handling loose screws or driving them manually. Screws install by inserting stick in driver,...

Read More »
Converters

Device Converter simplifies multilayer PCB prototyping.

Actel device converter - DC-AX2000/RTAX2000S-01 allows users to implement commercial Axcelerator® FG896 package during prototyping, and then switch to equivalent CQ352 package for production. Soldered directly onto SMT QFP pads, product is designed to receive AX2000 Actel Axcelerator® Family FPGAs on top and converts pin mapping to RTAX2000S Actel Radiation-Tolerant FPGAs. Unit...

Read More »
Controls and Controllers

Hybrid Torque Control System provides precision operation.

Accommodating assembly industry demands for repeatable, cell-based torque driver, HD Series uses both air and electric power to set and control torque. Pneumatic pressure sensor and algorithm enables precision digital torque selection, while brushless DC motor provides repeatable torque control. Adjustable torque and parameter settings occur with one touch on front panel or via PLC signal. Torque...

Read More »
Reels

Sequentially Printed Cable Reel shows accurate wire length.

True Sequential Footage(TM) cable reel uses footage mark to document remaining wire, beginning with zero at bottom of reel and ending with finished length at top. This mark allows for identification of re-order point and ultimately controls end-of-reel scrap. Precision is ensured with use of Doppler lasers, and unit's non-contact capabilities allow for zero slip and zero wear.

Read More »
Carpet Cleaning Machine suits residential and commercial jobs.
Carpet Extractors

Carpet Cleaning Machine suits residential and commercial jobs.

Powered by 23 hp Briggs and Stratton engine, Boxxer 323 truckmount enables carpet cleaning techs to clean carpets and hard-surface floors as well as pressure wash using same machine. Ability to deliver heated water up to 210°F and pressures up to 2,500 psi promote cleaning efficiency, while 70 gal recovery tank enables extended run times for optimal worker productivity.

Read More »
Grippers (Tools)

Adjustable Bag Gripper handles bag weights from 5-55 lb.

Adjusted using hand wheel, model ABG-25 features 7/16 in. solid stainless steel fingers with radiused ends and independent decker plates for accurate bag placement on tight pallets. Pneumatic valves provide complete open/close cycle in less than .6 sec. Designed to handle bags from 7.25-21 in. wide, 12-36 in. long, and 1-6 in. thick, ABG-25 is suited for palletizing plastic, woven cloth, and...

Read More »
Blades

Owens Corning Unveils Ultrablade(TM) High-Performance Fabrics to Support Market Shift to Longer, Lighter, Stiffer Wind Turbine Blades

Solutions enable designers to remove nearly a metric ton of fabric and resin from 2.0 Megawatt wind turbine blade sets compared to using standard Eglass reinforcement BEIJING, -- Owens Corning (NYSE:OC), a leading global producer of reinforcement solutions for composite systems and residential and commercial building materials, today introduced Ultrablade(TM) fabric solutions to help enable the...

Read More »
CFR ECO-500 up for ISSA Innovation Award
Carpet Extractors

CFR ECO-500 up for ISSA Innovation Award

Recycles and Filters Cleaning Solution Chicago, IL - CFR®, which manufactures midsized recycling carpet extractors and other carpet cleaning tools and equipment, has proudly entered its carpet extractor, the ECO-500, into this year's ISSA/TRADESHOW® 2010 Innovation Award Program. The Innovation Award Program recognizes ground-breaking products and services that benefit the industry, helping...

Read More »

All Topics