Automatic Blind Riveter has portable, hand-held design.

Enabling auto-feed riveting, AutoSet(TM) features one-touch cycle mechanism allowing one hand to be free to hold application while riveting. Capable of setting approximately 30 rivets per min, product can be reloaded in less than 10 sec. Additional features include tape loaded rivets, vacuum rivet-holding system, built-in mandrel collection system, and 3-piece jaws. Instrument uses POPÂ-®...

Read More »

Digital Microgage simplifies factory alignment.

Laser Microgage 2000 checks mechanical straightness, slide and stage runout, surface flatness, machine parallelism, and mechanical squareness. It works with laser transmitter, which projects collimated laser reference beam that is captured by receiver connected to digital display. MG-2000 operates over range of a few inches to 80 ft and provides readings accurate to 0.0001 in. It can connect to...

Read More »
Flat Cable Stripper strips cable on one or both sides.

Flat Cable Stripper strips cable on one or both sides.

Model D109 strips flat cables with round or rectangular, stranded or solid conductors up to 4Â-¼ in. wide and 3/16 in. thick. Using FybRglassÂ-® stripping wheels, unit strips cable 1/8, 1/4, or 1 in. wide depending on selected wheel. Custom wheels are available for larger or smaller width cables. Strip position can be set for up to 1 7/16 in. from cable end. Conductors are left undamaged...

Read More »
Autofeed Screw System features slip-resistant nose piece.

Autofeed Screw System features slip-resistant nose piece.

Series P13 long-extension autofeed screw gun handles 1-3 in. screws in #6 to #12 diameters. Total length of gun with extension is 40 in. Polyethylene covering keeps nose in place as screws are fastened at rates of one every 2-3 seconds. Model P13KDE features dedicated extension, while Model P13KUE has universal/removable extension. Series is suited for drywall and roofing and allows sub-floor and...

Read More »

Tools enable robots for laboratory applications.

Solution package enables system integrators and end users to acquire robotic tools necessary for laboratory automation applications. Suite of products includes servo and pneumatic grippers, microplate handling fingers, microplate hotels, tool changers, and collision sensors, all of which can be applied to user's choice of motion systems. Serial Servo Gripper is designed for open architecture and...

Read More »
Combination Shear/Plier cuts wire, grips, and forms leads.

Combination Shear/Plier cuts wire, grips, and forms leads.

Model 475C combines full by-pass shear cutter and short nose plier into one hand tool. It is constructed from high carbon steel and has soft Xuro-Rubber(TM) cushioned hand grips and Light Touch(TM) return spring. Precise enough to grasp one human hair, product cuts up to 12 AWG copper wire. Tool is suited for various types of assembly and wire processing.

Read More »
Boiler Tube End Prep Tool fits into tight areas.

Boiler Tube End Prep Tool fits into tight areas.

Esco Mongoose MILLHOGÂ-® right angle drive ID clamping end prep tool utilizes push-pull clamp and release mechanism with attached wrenches to bevel tubes with 5/8 in. ID to 3 in. OD. Its 2/3 hp pneumatic motor generates cutting torque at the bit capable of machining stainless steel and alloyed tubing. Suitable for performing any angle of prep, tool includes dual opposed tapered roller...

Read More »
Crimping Tool measures 5.75 in. long and weighs 1.5 lb.

Crimping Tool measures 5.75 in. long and weighs 1.5 lb.

Micro-pneumatic crimping tool is hand actuated and operates on 90 psi air pressure. When used with compatible crimping heads, product typically crimps terminals and splices to 26-14 AWG wire. In some cases, acceptable wire range is 22-10 AWG. Tool may be outfitted with double-action crimp head, T-HEAD crimper, or straight-action crimp head. General-purpose tool suits intermediate production...

Read More »
Micro Grippers suit automation applications.

Micro Grippers suit automation applications.

Delivering pick and place service, grippers feature blank fingers that are profiled to fit small parts. Finger sets can be exchanged without disturbing mounting setup, close with spring force, and open with plant air using valves on 3-way control circuits. Products are offered in 5 micro sizes, in 3 basic configurations, and in 4 mounting styles with choice of aluminum alloy or stainless steel...

Read More »

All Topics