Paints

Latex Coating paints interior and exterior walls.

Devflex 4205 semi-gloss, waterborne, acrylic latex coating can be applied to properly prepared surfaces including drywall, wood, masonry, and metal surfaces in institutional, commercial and light industrial areas. Low-odor, low-VOC latex dries quickly and cleans up with soap and water. Non-yellowing coating applies by brush, roll or spray. It is available in white and colors.

Read More »
Document Handler laminates and binds.
Laminators

Document Handler laminates and binds.

Tandem+ Deluxe Personal Laminator/Document Binder incorporates 2-roller pouch laminator, thermal binding station, and cooling station. It can laminate and protect documents up to 9 in. wide and 5 mils thick. It binds up to 120 pages of letter size or A4 covers. Applications include professionally finishing graphic presentations such as signs, POP displays, certificates, posters, countertop signs,...

Read More »
Primers

Reformulated Primers have lower VOCs.

Improvements to Enviroline(R) 58 and Enviroline(R) 59 include easier mixing, lower VOCs, no need for special thinners, and color changes. Enviroline 58 is now available in tan for greater contrast from IECC topcoats, and Enviroline 59 is lighter color to increase hiding ability of Envirothane(TM) 535 Urethane topcoat. Enviroline 58 is epoxy polyamide rust inhibitive primer; Enviroline 59 is for...

Read More »
Floor Coating resists dirt and abrasion.
Coatings

Floor Coating resists dirt and abrasion.

Concord(TM) polyurethane high gloss enamel resists mild acid and alkali fumes, oil, grease, gases, steam, dirt and abrasion. It is USDA approved for surfaces where there is possible food contact in facilities operating under Federal Meat and Poultry Products Inspection Program. Coating rolls or brushes on and dries to hard, crystal-clear or color finish that is easy to clean and maintain. It...

Read More »
Black-Body Coating is odorless and water-soluble.
Coatings

Black-Body Coating is odorless and water-soluble.

With emissivity greater than 0.90, HiE-Coat(TM) 840-C coating improves thermal efficiency of combustion and exhaust pipes as well as oven and furnace walls to 2500° F. Coverage rate is approximately 500 sq ft/gal (2 mil dry film thickness), and curing is accomplished in operation or by heating for 1-2 hours at 2000° F. HiE-Coat 840-M is used for coating carbon and stainless steel...

Read More »
Inks

Silicone Ink retains flexibility in low temperatures.

115-08 electrically conductive, silicone-based ink and coating is suitable for dip coating and spraying. Its temperature range is from -180 to 250° C. Suitable for EMI/RFI shielding applications, 115-08 resists cracking, and adheres to silicone substrates. Volume resistance is rated at 0.00012 Ohm-cm and sheet resistivity is 0.05 Ohm/sq/mil. Non-solderable ink is thermally stable to...

Read More »
Coatings

Mold Release Coating comes in aerosolized formulation.

Frekote® S-20 silicone rubber mold release coating eliminates need for spray equipment. It is designed for use in mold temperatures from 140 to 375 deg F, and is effective replacement for fluorocarbon-based release agents. Coating performs well in applications where minimal mold buildup and non contaminating transfer are required. In addition to 11.5 oz aerosol spray cans, Frekote S-20 is...

Read More »
Colors

Flair Finishes are used in rotational molding applications.

Chroma-Flair(TM) finishes provide look of pearl finish. Complete line of flair finishes are used on rotational molded parts and are available in alternative color selections, including blue and orange base colors. Effects vary by pellet count per gram. Finishes can be used for outdoor applications and for special effects.

Read More »
Fluorescent Paints provide maximum coverage on metal and wood.
Paints

Fluorescent Paints provide maximum coverage on metal and wood.

Available in orange, red, red/orange and green, Industrial Tough Coat® I.D. fluorescent paints provide visibility for labeling, coding, and marking of all steel substrates. Paints dry to touch in 15 minutes (77 deg F, 50 relative humidity), allowing for production speed marking. Suitable for identification of inventoried parts, materials, and work-in-progress, paints have high solids...

Read More »
Color Change Powder System operates at 1000 CFM.
Paint Booths

Color Change Powder System operates at 1000 CFM.

QualityCoat(TM) ColorChange booth includes removable cartridge module for color change. Variable speed motor drive controls booth containment air. It has built-in self-diagnostics, and provides motor status readout, voltage surge protection, and phase loss detection circuits. Fan speed can be preset or infinitely variable. Unit is equipped with electrical control panel and booth pneumatic control...

Read More »

All Topics