NSF-Approved Coatings suit potable water applications.
Coatings

NSF-Approved Coatings suit potable water applications.

Macropoxy® 646 NSF Fast Cure Epoxy is a fast-drying polyamide epoxy for steel and concrete structures. At 77°F and 50% relative humidity, it dries to touch in 2 hrs. Macropoxy® 846 NSF Winter Grade Epoxy is a fast-drying polyamide epoxy for industrial application maintenance and can be applied at temperatures as low as 35°F. It cures to touch in 4-5 hrs at 40°F, 50% relative humidity. Both...

Read More »
Epoxy Coatings suits water/wastewater treatment industry.
Coatings

Epoxy Coatings suits water/wastewater treatment industry.

Formulated using modified phenalkamine epoxy, Dura-Plate 235 NSF Multi-Purpose Epoxy is a VOC-compliant coating that delivers chemical- and corrosion-resistance. With flash point greater than 200°F, product withstands application temperatures from 0-120°F. Dura-Plate UHS NSF Primer ultra high solids amine epoxy adheres to pitted steel and concrete surfaces. Able to achieve 8 mil wet...

Read More »
Coatings

Coating Material provides abrasion resistance.

WEAResist(TM) polymer/ceramic coating can be applied to virtually any surface requiring protection from harsh operating environments. It remains pliable when cured, absorbing impact and improving abrasion resistant properties. One-part formulation requires no mixing. WEAResist(TM) will fully cure in 8 hours at temperatures from 0-210°F. Applications include elbows, pipe linings, impact...

Read More »
Acrylic Conformal Coating now available in aerosol can.
Coatings

Acrylic Conformal Coating now available in aerosol can.

Suited for printed circuit and printed wire assemblies, moisture-resistant 1B31 clear conformal coating allows users to make quick repairs, cost-efficient prototypes, low cost retrofits and small production runs. Product contains UV safety tracer for inspection under black light and is MIL-I-46058C and IPC-CC-830 qualified. It is available in liquid bulk packaging in quarts, gallons, 5-gallon...

Read More »
Polymer produces high-solids floor finishes.
Finishes

Polymer produces high-solids floor finishes.

Megatran® 248 produces floor finish formulations that are easily applied and repaired, and perform well over wide range of temperatures and humidities. Glossy finishes respond well to burnishing, low-speed spray buffing, and frequent ultra-high-speed maintenance. Use of sulfate and sulfonate groups attached to polymer backbone stabilize polymer emulsion particles during drying process.

Read More »
Water-Based Epoxy suits industrial/marine applications.
Epoxies

Water-Based Epoxy suits industrial/marine applications.

Fast Clad(TM) DTM, single-coat, direct-to-metal epoxy finish, provides high film build in one coat of 4-6 mils dry film thickness. Product dries to tough gloss finish, providing corrosion and chemical resistance as well as weathering protection. Applied at 77Â-ºF, it dries to touch in 45 min and is dry to handle in 4 hr. Low-odor coating meets VOC and HAPS requirements, cleans up with water,...

Read More »
Pure Diamond Grade provides wear resistance.
Cutting Tool Inserts

Pure Diamond Grade provides wear resistance.

Type KD1405 pure diamond cutting tool material can increase tool life 100-200% relative to conventional PCD tooling on continuous to lightly interrupted turning, finishing, and semi-finishing milling applications. Material is produced using chemical vapor deposition applied by plasma torch method, providing pure diamond microstructure that is tough enough to withstand milling operations. KD1405...

Read More »
Release Agents

Release Agent is suited for flange sealing.

Frekote® EFR, formulated to seal porous flange surfaces on composite molds, provides multiple releases per application. Semi-permanent, polymeric release agent is also suited for abrasive processes such as polymer concrete molding. High slip coating is capable of releasing highly filled and abrasive compounds and may be applied at temperatures ranging from 55 to 110°F.

Read More »
Biocompatible Dielectric Material suits medical devices.
Coatings

Biocompatible Dielectric Material suits medical devices.

High strength toughened fluoropolymer (HSTF), produced through manipulation of PTFE microstructure, offers scrape abrasion resistance, cut-through resistance, and dielectric strength of 1.4 kV/mil in pinhole free profiles as thin as 0.0005 in. Material can be applied over conductors as small as 50 AWG wire. Applications include electrophysiology products and other catheter-based products where...

Read More »
Cut and Bevel Pipe up to 63" Diameter with a Single Lightweight, Portable Machine
Sponsored

Cut and Bevel Pipe up to 63" Diameter with a Single Lightweight, Portable Machine

CS Unitec is a leader in power tools designed for industrial applications, with products that set the standard for robust performance and industry-leading reliability. Adding to our long list of innovation is a new line of pipe cutting machines. For cutting and beveling pipe up to 2" in thickness and diameters from 12" to 63", no other cutting system comes close. See our video to learn more.

Read More »

All Topics