Polymer produces durable floor finish.
Finishes

Polymer produces durable floor finish.

Megatran® 233 features high gloss characteristics with scuff and scratch resistance. Due to high solids content, formulations based on Megatran 233 polymer require fewer coats than are needed with conventional lower-solids formulations. Use of sulfate and sulfonate groups attached to polymer backbone stabilize polymer emulsion particles during drying process. Finishes respond well to...

Read More »
Aerosols provide mold release and lubrication.
Solid Film Lubricants

Aerosols provide mold release and lubrication.

Economy Silicone-55L Mold Release contains 5% silicone concentration. It does not contain CFC's, HCFC's, Class 1 or Class 2 substances and can be used for food-packaging applications. Heat-resistant Die Makers Lubricant-L, with Teflon®, is blended to not dry and to minimize bleeding out with ejector pins, knockouts, slides, cams, and all moving parts. Teflon® additive minimizes...

Read More »
Corrosion Inhibitor suits off-shore applications.
Coatings

Corrosion Inhibitor suits off-shore applications.

VpCI®-609 provides environmentally acceptable and biodegradable corrosion protection for interiors of HRSG and HVAC equipment, piping, and tanks. With zero bioaccumulation potential, product provides up to 24 months of continuous corrosion protection including liquid, vapor-phase, and interface protection above liquid level. It has neutral pH and does not contain nitrites, phosphates, heavy...

Read More »
Waterproof Coating simplifies concrete applications.
Coatings

Waterproof Coating simplifies concrete applications.

Barricoat(TM) water-based asphalt emulsion, modified with synthetic rubber and additives, forms monolithic, flexible membrane without use of primers. Waterproofing and vapor-retardant membrane can be applied to concrete, CMU, wood, and metal. Non-flammable, solvent-free system is offered in 2 types: Barricoat-S single-coat spray application, and Barricoat-R double-reinforced roller applied system.

Read More »
Bulbs Buying Guide
Sponsored

Bulbs Buying Guide

While it might seem easy to pick a light bulb, there are actually numerous factors to take into consideration. This buying guide will explain each type and the important attributes you should consider when sourcing bulbs.

Read More »
Glass Coatings reduce home energy consumption.
Coatings

Glass Coatings reduce home energy consumption.

Certincoat® Low E flat glass coatings, for window manufacterers, are pyrolytic hard coatings for cold climates. They carry high solar heat gain coefficient to utilize sun's energy. Solar Selective SunE(TM) glass coatings, developed for hot climates, are hard ceramic coatings that cut energy costs by combining solar selectivity with low emissivity. Specialty glass coatings provide...

Read More »
Nickel passes 180° bend test per Mil-C-26074.
Nickel

Nickel passes 180° bend test per Mil-C-26074.

Nitec 9500 pH-regulated, 6-9% phosphorus electroless nickel is for use over steel, copper, brass, magnesium, aluminum, and other base metals. Product combines high-speed deposition and deposits that remain bright through 8 turnovers. Normal replenishments of stable, 3-component bath automatically regulates solution pH.

Read More »
Multisurface Coating inhibits growth of microorganisms.
Paints

Multisurface Coating inhibits growth of microorganisms.

Self-priming 24/7 Coating with Microban® Antimicrobial Product Protection inhibits growth of odor and stain-causing bacteria, mold, and mildew on coating film. Microban additives are EPA registered and will last life of coating by guarding against degradation caused by microorganisms. Coating cleans up with soap and water and is suitable for lined and unlined HVAC duct systems, previously...

Read More »
Booth Coating is water-based and goes on in seconds.
Coatings

Booth Coating is water-based and goes on in seconds.

Fast-Dry Peelable Coating is free of both VOCs and heavy metals. Single-component, non-flammable liquid coating is virtually odor-free and can be applied to metals, plastics, glass, and any other nonporous material using standard spray equipment. It is also applicable via brush and can be used as edge protector. Product complies with OSHA regulations and has reflective white surface that enhances...

Read More »
TiAlN Tool Coating protects against wear.
Coatings

TiAlN Tool Coating protects against wear.

Suited for use in molding and stamping/forming applications, BALINIT® LUMENA nano-layered coating exhibits hardness of 3400 HV 0.05 and thickness from 8-15 µm. In molding, wear-resistant product offers optimized ratio between hardness and internal stress as well as protection against heat penetration into tool. For stamping and forming, coating absorbs shear stress and reduces heat transfer...

Read More »
TiAIN Coating suits turning and milling tools.
Coatings

TiAIN Coating suits turning and milling tools.

BALINIT® ENDURA offers optimization potential with turning and milling tools in highly abrasive applications. High metal removal rates can be realized by cutting with high speed and feed rates simultaneously. Coating provides protection against abrasive wear. Ratio of residual compressive stress to hardness stabilizes tool cutting edge under high loads, and increased thickness reduces heat...

Read More »
How SpinSelect Can Save You Time and Money
Sponsored

How SpinSelect Can Save You Time and Money

Thanks to the unique SpinSelect™ Multi-Pocket selectable quick change tool holder, it's time to rethink the range, complexity and volume of parts that your lathe can produce. Our Spin-Select™ tool was created to increase productivity and consistency by decreasing downtime associated with lathe cutting tool and insert setups or changeovers. This product is a game-changer for the industry and we're pleased to show you why.

Read More »

All Topics