Paints & Coatings

Related Categories
Paints & Coatings

Stainless Steel Paint protects metal.

May 16, 2002

Duralco(TM) 6105 SP Stainless Steel Paint combines corrosion resistance of 316L stainless steel with 1200 deg F temperature protection. Protective coating cures overnight at room temperature (or air dries in 15 to 30 minutes) to form protective layer of stainless steel. Suitable for protecting metal pipes, stacks, boilers, furnaces, and heat exchangers, paint coats and protects up to 30 square ft... Read More

Adhesives & Sealants, Paints & Coatings

Sealant protects chrome plated tools.

May 15, 2002

Dri-Touch(R) topcoat penetrates and protects recessed areas of parts that can rust prematurely due to thin plating deposits. It can also be applied to hand tools, fixtures, castings, forgings, powdered metal, dies, and partially finished components in service or storage. Coating will not drain or wick off into packaging, thus maintaining effective, long-term barrier against humidity and... Read More

Paints & Coatings

Floor Finish suits high-speed maintenance programs.

May 07, 2002

Gallery ultra high speed (UHS) floor finish provides wet-look gloss and responds quickly to UHS burnishing. It provides mark resistance and durability. Read More

Paints & Coatings

High-Temperature Paint provides corrosion protection.

May 07, 2002

Single-part, aluminum-rich Corr-Paint(TM) CP4010 ceramic-silicone based coating protects steel components and structures for applications to 1200 deg F. It is resistant to acids, bases, and solvents, and provides thermal-shock, salt-spray, and UV resistance. Water-dispersible coating dries at room temperature and cures fully during operation at temperatures above 450 deg F. Non-flammable, low VOC... Read More

Paints & Coatings, Plant Furnishings & Accessories

Powder Coat Paint adheres to steel.

Apr 29, 2002

PowderCoatplus(TM) powder coat paint on cold rolled steel is rust resistant, is environmentally sound, and adheres to edges. System involves 3 steps: pretreatment for removing lubricating oils from steel surface, 2 mil thick coating of powder coat enamel applied in automated electrostatic spray booth, and baking finish to hard surface. Paint resists salt spray and impact tests. Read More

Adhesives & Sealants, Chemicals & Chemical Processing, Paints & Coatings

Adhesive/Sealant bonds and encapsulates.

Apr 29, 2002

MNRC 04-1347 UV light curing resin is based on aliphatic urethane acrylate monomer blend. At 1 mil thickness, it cures in 10 to 15 seconds with UV light. Transparent liquid is suitable for clear bonds or encapsulation. It bonds to metal, ceramic, glass, and many plastics. MNRC 04-1347 is thixotropic at 25 deg C, and cures to 40-50 Shore A with elongation of 150%. Operating temperature range is... Read More

Material Handling & Storage, Paints & Coatings

Finishing System produces product in 10 to15 minutes.

Apr 17, 2002

BK-TT Mini TRU TEMP(R) part finishing system utilizes black process to provide corrosion protection on castings and powdered metal parts. Two-step chemistry creates black magnetite finish, which is Mil Spec compliant, measures .000020 in. thick, and can withstand 100 to 300 salt spray exposure. Supplied as turnkey system, components include 7 tanks and covers, 2 hot plates, and all chemicals... Read More

Paints & Coatings

Marking Paints work on most surfaces.

Apr 08, 2002

Krylon(R) Industrial Quik-Mark Inverted Marking Paints have Spray-Thru(TM) cap and non-clogging spray tip that create bright, highly-visible markings on concrete, pavement, gravel, grass, soil, brick, asphalt, and excavation sites. Also available are APWA solvent-based marking caulks, for temporary markings up to 30 days. They can be removed from hard surfaces with wire brush and water.... Read More

Paints & Coatings

Latex Coating paints interior and exterior walls.

Apr 08, 2002

Devflex 4205 semi-gloss, waterborne, acrylic latex coating can be applied to properly prepared surfaces including drywall, wood, masonry, and metal surfaces in institutional, commercial and light industrial areas. Low-odor, low-VOC latex dries quickly and cleans up with soap and water. Non-yellowing coating applies by brush, roll or spray. It is available in white and colors. Read More

Paints & Coatings

Reformulated Primers have lower VOCs.

Mar 14, 2002

Improvements to Enviroline(R) 58 and Enviroline(R) 59 include easier mixing, lower VOCs, no need for special thinners, and color changes. Enviroline 58 is now available in tan for greater contrast from IECC topcoats, and Enviroline 59 is lighter color to increase hiding ability of Envirothane(TM) 535 Urethane topcoat. Enviroline 58 is epoxy polyamide rust inhibitive primer; Enviroline 59 is for... Read More

Paints & Coatings

Black-Body Coating is odorless and water-soluble.

Mar 13, 2002

With emissivity greater than 0.90, HiE-Coat(TM) 840-C coating improves thermal efficiency of combustion and exhaust pipes as well as oven and furnace walls to 2500° F. Coverage rate is approximately 500 sq ft/gal (2 mil dry film thickness), and curing is accomplished in operation or by heating for 1-2 hours at 2000° F. HiE-Coat 840-M is used for coating carbon and stainless steel panels and... Read More

Architectural and Civil Engineering Products, Paints & Coatings

Floor Coating resists dirt and abrasion.

Mar 13, 2002

Concord(TM) polyurethane high gloss enamel resists mild acid and alkali fumes, oil, grease, gases, steam, dirt and abrasion. It is USDA approved for surfaces where there is possible food contact in facilities operating under Federal Meat and Poultry Products Inspection Program. Coating rolls or brushes on and dries to hard, crystal-clear or color finish that is easy to clean and maintain. It... Read More

Chemicals & Chemical Processing, Paints & Coatings

Mold Release Coating comes in aerosolized formulation.

Mar 12, 2002

Frekote® S-20 silicone rubber mold release coating eliminates need for spray equipment. It is designed for use in mold temperatures from 140 to 375 deg F, and is effective replacement for fluorocarbon-based release agents. Coating performs well in applications where minimal mold buildup and non contaminating transfer are required. In addition to 11.5 oz aerosol spray cans, Frekote S-20 is... Read More

Materials & Material Processing, Paints & Coatings

Silicone Ink retains flexibility in low temperatures.

Mar 12, 2002

115-08 electrically conductive, silicone-based ink and coating is suitable for dip coating and spraying. Its temperature range is from -180 to 250° C. Suitable for EMI/RFI shielding applications, 115-08 resists cracking, and adheres to silicone substrates. Volume resistance is rated at 0.00012 Ohm-cm and sheet resistivity is 0.05 Ohm/sq/mil. Non-solderable ink is thermally stable to 325°C,... Read More

Materials & Material Processing, Paints & Coatings

Flair Finishes are used in rotational molding applications.

Mar 11, 2002

Chroma-Flair(TM) finishes provide look of pearl finish. Complete line of flair finishes are used on rotational molded parts and are available in alternative color selections, including blue and orange base colors. Effects vary by pellet count per gram. Finishes can be used for outdoor applications and for special effects. Read More

Adhesives & Sealants, Paints & Coatings

Fluorescent Paints provide maximum coverage on metal and wood.

Mar 08, 2002

Available in orange, red, red/orange and green, Industrial Tough Coat® I.D. fluorescent paints provide visibility for labeling, coding, and marking of all steel substrates. Paints dry to touch in 15 minutes (77 deg F, 50 relative humidity), allowing for production speed marking. Suitable for identification of inventoried parts, materials, and work-in-progress, paints have high solids content... Read More

HVAC, Machinery & Machining Tools, Paints & Coatings

Color Change Powder System operates at 1000 CFM.

Feb 27, 2002

QualityCoat(TM) ColorChange booth includes removable cartridge module for color change. Variable speed motor drive controls booth containment air. It has built-in self-diagnostics, and provides motor status readout, voltage surge protection, and phase loss detection circuits. Fan speed can be preset or infinitely variable. Unit is equipped with electrical control panel and booth pneumatic control... Read More

Paints & Coatings, Services

Conformal Coatings are environmentally friendly.

Feb 14, 2002

UL-listed Series 1H coatings are non-flammable, non-hazardous to handle, and suitable for moist conditions. Water replaces solvents in acrylic and polyurethane coatings. Coatings offer stability, flexibility, and chemical resistance. Optimal performance is reached with thin coatings that can be applied by robotic selective coating systems, to control thickness for maximum economy, or by dipping... Read More

Adhesives & Sealants, Paints & Coatings

UV Coatings suit fiber-optic applications.

Feb 04, 2002

15C, 15D, and WCC2B one-part, UV fiber-coating materials are suitable for application to optical fiber. Adhesives can be supplied for miles or millimeters of cable. Adhesives protect cable behind fiber-optic devices and limit process time. Read More

Paints & Coatings

Powder Coat Finish is environmentally friendly.

Jan 29, 2002

SpectraShield powder coating finish is applied to components of rolling doors and rolling counter doors. It provides color retention, UV stability, and resistance to corrosion, chemicals and abrasion. Its total palette consists of more than 200 colors. SpectraShield gray powder coating is used on all of company's exposed steel door surfaces including guides, bottom bar, and endplate brackets. Read More