New Optics & Photonics Products

Interferometer provides on-line part inspection.

Installed on manufacturing line, TopCam TMS-300/320 verifies production part flatness and topography. It can be controlled via operator interface software using COM/ActiveX or LabView(TM) drivers. Telecentric lenses allow imaging along high, steep edges and within deep, drilled holes. Measurements of surfaces with substantial relief are characterized by scanning Z dynamic range of 50 mm. Camera...

Virtual Labels help eliminate production downtime.

DataLase non-toxic ink, coating, or substrate additive produces positive image when marked by low power CO2 laser. It undergoes chemical color change and creates stable, high-contrast image. DataLase allows images such as barcodes, 2D codes, logos, and graphics to be imaged by CO2 laser directly onto any surface, eliminating need to use adhesive labels on packaging. Virtual label becomes integral...

Camera meets traffic control application requirements.

Measuring 120 x 50 x 40 mm, CV-M2CL is based on 1 in. format Kodak CCD sensor (KAI-2001) and features auto iris output, knee and gamma response curves, and analog monitor output. With 2 megapixel resolution (1600 x 1200), it also provides 5-image burst trigger, which allows capture of sequence of 5 images at different shutter speed settings. Camera is also suited for industrial inspection,...

Laser Sensors offer long stand-off and measurement range.

Series DLS-2000 single point laser sensors have offset distances of 4.0 in., 10 in., or 19.7 in. for long-range version. They deliver 25 micron resolution at 1.8 kHz scan rate, 1.667 kHz for long-range version. Measurement range is 11.8, 24, or 118 in. with accuracy of Ã-

OPTICS IN THE SEMICONDUCTOR INDUSTRY

This white paper provides an in-depth overview into optics in the semiconductor industry.

Camera provides SNMP-based environmental monitoring.

Integrating camera with multiple sensors, cameraProbe8 can log sensor data and associated image. Equipped with Linux, unit features 32-bit ARM processor, 64 Mb Flash, and 64 Mb SDRAM along with 10/100 Mbps Ethernet and 2 serial ports. Image sensor incorporates Sony CCD requiring .5 Lux at f1.2. Direct drive stepper motor enables users to pan and tilt camera via web browser. Eight intelligent...

Spectrometer analyzes all common elements in metals.

Able to analyze Nitrogen levels in steel down to 20 ppm, SPECTROMAXx incorporates ICAL intelligent calibration logic, which monitors system integrity and virtually eliminates need for recalibration samples. Unit is also equipped with Argon Saver Mode and readout system that minimizes analysis time. Spectrometer is available as bench-top unit or floor model to fit various work load or space...

Retention Mechanism protects graphics card.

Board-level retention mechanism for PCI Express graphics cards protects against electrical interrupts and mechanical damage caused by system-level shocks and vibration. Flexible arm extends away from slot and includes molded post that snaps into notch on bottom of add-in card. Device solders to motherboard adjacent to x16 PCI Express card edge connector, and engages with hockey stick shaped hook...

Miniature Camera operates in dual wavelengths.

Visible-InGaAs MiniCamera simultaneously images in visible and near-infrared waveband regions. Unit features 320 x 240 pixel array with 40 micron pitch and spectral response from 400-1,600 nm. Peak quantum efficiency is 80% at 1,310 nm and 70% at 1,550 nm. Thermoelectrically temperature stabilized unit has no moving parts and weighs less than 300 g. It simultaneously delivers 12-bit, RS-422...

Stanchions add 4th or 5th axis to T-slotted frames.

Quick Clamp Stanchions are available in over 40 standard models, including single or double shaft bases, blank or pre-drilled mounting plates, and single or double mounting blocks in 1, 1.5, and 2 in. bore sizes. Adjustable without use of tools, devices allow user to precisely position camera equipment, scanning devices, light sources, photo sensors, computer monitors, and actuators.

Grounding Connector suits parallel-through applications.

ERITECHÃ-® HAMMERLOCK joins grounding conductor to ground rod with one hammer strike. Machined from electrolytic copper, connection is conductive and withstands ground fault currents and lightning transients. Dual-hole version, available for No. 6 and No. 4 solid, is suited for pad-mounted transformer applications. Larger version of single-hole product permits 2/0 stranded to be joined to 5/8...

ISO-Certified Precision Machining and Contract Manufacturing Services from DFF

DFF is an industry leading contract manufacturer specializing in medium to high production precision machined components and electromechanical assemblies. Our 100 CNC machining centers and design-assist capabilities ensure our customers' needs are always met. Check out our video to learn more.