Flat Panel Monitor Tilt Mount holds 32-63 in. displays up to 180 lb.
Mounts

Flat Panel Monitor Tilt Mount holds 32-63 in. displays up to 180 lb.

Designed to hold digital signage flat panels with max hole pattern of 810 x 530 mm, Model FP-LDSB has adjustable tilt of -5° to +15° in lockable 5° increments. Sectional wall plate can be integrated with multiple mounts to create video wall. Featuring shallow profile of 2.5 in. from wall, Model FP-LDSB comes in black powder coat finish and can hold panels in portrait or...

Read More »
Motorized Kinematic Mount delivers high-resolution movement.
Optical Mounts

Motorized Kinematic Mount delivers high-resolution movement.

Motorized Kinematic Mount offers kinematic movement with 10.5° of angular travel and 0.264° per motor revolution. Once mount moves to desired position, it reports position via RS-232 connection and will maintain that position even without power applied. Potentiometers, located on back, can be used to manually move mount at speeds from 1.5 Â-µrad/sec to 60 mrad/sec. Each...

Read More »
Antenna Mounts

Compact In-Vehicle Mobile Antenna Mount integrates GPS.

Larsen brand new Motorola high-frequency mobile antenna mount has integrated active GPS antenna that provides coverage for vehicle tracking and location applications. Operating over frequency range of 27 MHz to 6 GHz, IP65-rated mount has input voltage of 3 or 5 Vdc and provides impedance matching at frequencies above 1 GHz. Device measures 4.5 x 2 x 0.7 in. and features mount center pin that...

Read More »
Dichroic Beamsplitter Holder provides 22 mm clear aperture.
Optical Mounts

Dichroic Beamsplitter Holder provides 22 mm clear aperture.

Designed to secure dichroic beamsplitters without affecting flatness, FH1 filter holder also allows for angle tuning or other motorized options. Opto-mechanical mount is optimized for 25.2 x 35.6 mm sized parts, and has flexibility to accept 1.0-2.0 mm thick components. Designed for use with VersaChrome(TM) tunable filters, holder also suits wide range of bench-top laboratory uses.

Read More »
Seal Stuff In, Seal Stuff Out
Sponsored

Seal Stuff In, Seal Stuff Out

One of the best ways to make sure that your machinery stays up and running in the face of adversity is to make sure that it's properly sealed. Of course, it's not always easy to determine whether the integrity of your seals are up to par. How can you tell when you have a problem?

Read More »
Motor Mount Kit and Gearbox adapt to Festo actuators.
Vibration Damping Mounts

Motor Mount Kit and Gearbox adapt to Festo actuators.

As bolt-on motor mounting kit and planetary gear head, LSK and EPL-H address challenges end-users experience developing and assembling brackets that connect motors and gearboxes to Festo® actuators. LSK customized mounting solution, offered in multiple sizes, is designed to connect any motor to linear actuator and includes coupling as well as mounting hardware. Offered in 3 frame sizes,...

Read More »
Laser Diode Mount includes internal cooling system.
Optical Mounts

Laser Diode Mount includes internal cooling system.

Handling up to 61 W thermal loads at 25°C, 764H-061 High Power Laser Diode Mount features internal thermoelectric coolers that enable fine wavelength tuning and optimal power output stabilization. Thermistor sensor is embedded into top plate for feedback loop temperature control and device also includes Model 3700 temperature controller. Unit has laser diodes, attached to top copper plate...

Read More »
Triangle Manufacturing Customizes Cost-Efficient Motor Mounts
Vibration Damping Mounts

Triangle Manufacturing Customizes Cost-Efficient Motor Mounts

Triangle debuts new product for the HVAC industry leading to lower cost and higher efficiency Oshkosh, Wisconsin - A large refrigeration manufacturer needed to replace a costly, cumbersome fan shelf with a smaller, more economical fan motor mount. Triangle Manufacturing Company, a custom bearing manufacturer, responded by taking a standard part and fully customizing it for a brand new...

Read More »
Elliptic Leaf Spring Antivibration Mounts are NATO-approved.
Vibration Damping Mounts

Elliptic Leaf Spring Antivibration Mounts are NATO-approved.

Impervious to corrosion and suited for shipboard applications, V10Z70-... Series employs 2 or more stainless steel U formed leaves to form elliptical shape when joined together in center portion with face plates. Spaces between U formed leaves are filled with polymer or stainless steel mesh, depending on model, that serves as damping compound. Operating over 50 to 86°F range, mounts feature...

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers