Connection Adapters are available with metric threads.
Flanges

Connection Adapters are available with metric threads.

ADAFLANGE(TM) ADAPTER with face seal is supplied with thru-hole flange. This combination adapts flange port to threaded connection. Supplied with threaded type companion flange, ADAFLANGEPORT(TM) adapts threaded connection to flange connection. Both adapters can be supplied with either clamp or threaded type companion flanges. They are available with 370 Flare, SAE Straight, ORS O-Ring Face Seal,...

Read More »
Bolt Adapters meet SAE specs.
Flanges

Bolt Adapters meet SAE specs.

ADAFLANGE(TM) Unified Code U61 4-Bolt and 2-Bolt Adapters mount on SAE Code 61 flange ports. 2-bolt flange adapters have bolt patterns that will mount on either of 2 diagonal tapped holes. 4-Bolt flange adapters may be qualified in higher pressure applications, and eliminate need for larger SAE Code 62 flange port patterns. Smaller flange footprints of both adapters permit ports to be nested...

Read More »
Turning and Milling Inserts are PVD coated.
Inserts

Turning and Milling Inserts are PVD coated.

SpectraTurn(TM)and SprectraMill(TM) inserts are coated with TiAln or AlTiN for edge strength and wear resistance. Heat produced in cutting process is carried away by chip. TiAlN coated insert grades are suitable for dry milling and for high-speed turning. AlTiN coated inserts are ideal for milling titanium and titanium alloys.

Read More »
One-piece Interfaces connect to power boards.
Connectors

One-piece Interfaces connect to power boards.

OPP Series one-piece power interface, rated up to 5 A, eliminates bent pin problems of multi-component devices. Connectors are soldered to main board and power board is attached by either metric or English mechanical fasteners. Interfaces are available with choice of 3, 7 or 10 contacts on 0.100 in. pitch. Optional alignment pins can be provided on top, bottom or both sides to ease processing,...

Read More »
Manipulating Arm has variable speed control.
Arms

Manipulating Arm has variable speed control.

Six-axis Mini-Articularm, mounted on top of omni-directional platform, suits lifting and handling operations. Controlled via corded push button remote controls, joysticks, or wireless radio frequency controllers, system is capable of handling 100 to 250 lbs at 72 in. radius. Parallelogram arm allows load to remain parallel to ground while being raised or lowered. It also rotates 360 deg, and is...

Read More »
Rotary Actuator loads and unloads machines.
Actuators

Rotary Actuator loads and unloads machines.

DRM is available with wide range of 2- and 3-finger parallel grippers. Pneumatic lines and electrical connections are plumbed through unit, eliminating wrapping and exposed lines. As part of DirectConnect(TM) system, grippers can be mounted without adapter plates. Unit is suitable for machining applications where one part needs to be exchanged with another. Four sizes are available with multiple...

Read More »
Gripper Fingers offer flexible part repositioning.
Workholding Systems

Gripper Fingers offer flexible part repositioning.

Rotary fingers for grippers allow 0 to 180 deg part repositioning while part is gripped. They are offered in 4 sizes with output torques from 0.4 to 11 Nm, and will accommodate wide range of parts. Housings are hard-coated aluminum. Double-acting, piston driven rack gear and gear train facilitate actuation while providing repeatable rotation. Thrust bearings support output shaft, and end...

Read More »
Receptacles support SCSI and FC-AL systems.
Connectors

Receptacles support SCSI and FC-AL systems.

SCA-2 receptacles consist of staggered contact heights which enable hot-plugging. Alignment guides at both ends house grounding contacts and allow blindmateability. SCA-2 receptacles are installed on backplane to mate directly with SCA-2 plugs installed on disk drive. Tail configurations include through-hole pin and press-fit compliant pin. 80-pin receptacle supports SCSI-3 protocol, while 40-pin...

Read More »
Reverse Expansion Insert presses into plastic hole.
Inserts

Reverse Expansion Insert presses into plastic hole.

Suitable for strengthening plastic joints, Series 18 brass reverse expansion insert is used in applications where bolt enters insert from headless end rather than from headed end. Its head provides high level pull-through resistance and its diamond knurl provides directional torque resistance for bolt installation. Unit does not require any specialized insertion tools, so it can be installed by...

Read More »
Encoders are available with connectors.
Encoders

Encoders are available with connectors.

Accu-Coder(TM) Cube Series and model 702, 725, 758, and 225 encoders are available with Eurofast connector. Connector allows user to reduce stocking requirements for cord sets and similar components since cords can be used for encoder connections and other components of motion control systems (such as proximity sensors and photoelectric switches).

Read More »
Paratherm™ HR Heat Transfer Fluid: Higher Temperature Stability Leads to Longer Fluid Life
Sponsored

Paratherm™ HR Heat Transfer Fluid: Higher Temperature Stability Leads to Longer Fluid Life

For the ultimate in heat transfer fluid performance, Paratherm offers HR Heat Transfer Fluid that is engineered specifically for closed loop liquid phase heating. When it comes to characteristics such as thermal stability and fluid degradation, Paratherm HR leads the industry in value and performance. See our video to learn how Paratherm is raising the bar for heat transfer fluids.

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers