Modules

New Power Entry Modules Integrate IEC Inlet and EMC Filter

New Power Entry Modules Integrate IEC Inlet and EMC Filter

DG12 and DG11 feature recessed 2-pole on/off rocker switch circuit breaker with 1 or 2-pole overcurrent protection. DG12 includes standard and low leakage mains filter as well as standard and high inductive performance options. Modules are IEC rated up to 10 A at 250 VAC and UL/CSA rated up to 15 A at 125/250 VAC.

Read More »
New FMC259 Fiber FMC+ Module Meets VITA 57.4 (FMC+) Specification

New FMC259 Fiber FMC+ Module Meets VITA 57.4 (FMC+) Specification

Offers dual board-mount optical assemblies, each providing 24 channel full-duplex transceivers capable of up to 28.1 Gb/s per channel. Provides clock data recovery and front-panel fiber I/O via MTP/MPO that has on board ultra-low jitter clock generator with two independent, fractional PLL. Features clocking that allow synchronization to an external clock input or on board and comes with LEDs in...

Read More »
New Rugged ECU Accelerates ADAS and Autonomous System Product Design

New Rugged ECU Accelerates ADAS and Autonomous System Product Design

RVP-TDA4Vx production-intent kit features TDA4VM SoC processor and configurable SerDes interface. Supports multiple SerDes capture streams with different transport protocols through its configurable personality card. Ideal for automated valet park, neural networks, video analytics, driver notification, multi-camera display, mirror replacement and sensor fusion applications.

Read More »
New AMC573 FPGA Board is AMC.1, 2, 3 and 4 Compliant

New AMC573 FPGA Board is AMC.1, 2, 3 and 4 Compliant

Utilizes the Xilinx XCZU28DR RFSoC and comes with onboard re-configurable FPGA which interfaces directly to the AMC FCLKA, TCLKA-D. Includes Trig-in, Trig-out, clock inputs, dual USB, dual serial ports and connector for external I/O. Features front panel that incorporates 18 high-density RF Coaxial connectors routed to the 8 ADC (12-bit @ 4 GSPS) and 8 DAC (14-bit @ 6.4 GSPS).

Read More »
Ballard-Powered Fuel Cell Tram-Buses from Van Hool Now in Revenue Service in France

Ballard-Powered Fuel Cell Tram-Buses from Van Hool Now in Revenue Service in France

VANCOUVER and PAU, FRANCE, Dec. 17, 2019 /PRNewswire/ - Ballard Power Systems (NASDAQ: BLDP; TSX: BLDP) today announced that 8 ExquiCity tram-buses built by Van Hool NV ( Van Hool ; www.vanhool.be) and powered by 8 Ballard FCveloCity®-HD 100-kilowatt fuel cell modules have been inaugurated at a ceremony in Pau, France and are now in revenue service in Pau's Bus Rapid Transit System....

Read More »
New Two I/O Modules Feature Spring-clamp Field Wiring Terminals

New Two I/O Modules Feature Spring-clamp Field Wiring Terminals

GRV-ITM-12 provides a high-density, low-cost temperature sensing option with two isolated zones and 6 channels per zone. Accurate to 0.1% of the configured range over 20-bit resolution for V/mV sensing with accuracy ranging from 2.0-5.0 °C for thermocouple sensing. GRV-CCANI-2 supports integrating CAN data into control applications using IEC 61131-3 languages.

Read More »
Richardson RFPD Announces Availability of Innovative All-in-one 5G mMIMO RF Power Amplifiers from NXP

Richardson RFPD Announces Availability of Innovative All-in-one 5G mMIMO RF Power Amplifiers from NXP

Portfolio of RF power multi-chip modules supports massive MIMO active antenna systems for 5G base stations December 3, 2019 – Geneva, Ill.: Richardson RFPD, Inc., an Arrow Electronics company, announced today the availability and full design support capabilities for the comprehensive RF power multi-chip module (MCM) portfolio for 5G mMIMO from NXP Semiconductors. These devices are part of...

Read More »
Precision Machining Solutions with Over 25 Years of Experience
Sponsored

Precision Machining Solutions with Over 25 Years of Experience

Quality, customer service, and unbeatable value are the hallmarks of Hogge Precision. Since 1989 we have built a reputation as the go-to precision machining source, servicing many demanding industries. For CNC machining and screw machining, there are few manufacturers that can match our capabilities and expertise. See our video to learn more.

Read More »

All Topics