Cable Blocks are construction grade.
Clip-On Block supports cable to 1 in. during pull-outs. Aluminum Roller-equipped Block is used on new strand or overlash work with cable to 2 in. Four-Roller Block supports multiple cables on nylon or aluminum rollers during new strand construction. Overlash Block handles cable or cable bundles up to 4 in. Model 73305 Block supports one cable up to 1 in. on new -¼ in. strand, and Model 75000...
Read More »
Cable Blocks are construction grade.
Clip-On Block supports cable to 1 in. during pull-outs. Aluminum Roller-equipped Block is used on new strand or overlash work with cable to 2 in. Four-Roller Block supports multiple cables on nylon or aluminum rollers during new strand construction. Overlash Block handles cable or cable bundles up to 4 in. Model 73305 Block supports one cable up to 1 in. on new Â-¼ in. strand, and Model 75000...
Read More »
Offset Block allows quick tool change.
Tool Length Offset Block eliminates lengthy tool setups, and chipped or broken tools. It allows user to touch off any type of tool in about 30 sec. All tools will be within .0001 in. of each other, eliminating question of which tool to adjust on first piece from setup.
Read More »
Offset Block allows quick tool change.
Tool Length Offset Block eliminates lengthy tool setups, and chipped or broken tools. It allows user to touch off any type of tool in about 30 sec. All tools will be within .0001 in. of each other, eliminating question of which tool to adjust on first piece from setup.
Read More »
The Advantages of Reshoring Your Manufacturing Operations
Bringing work back to the United States benefits your organization, customers, and the U.S. economy.
Read More »
Fuseblock facilitates installation in SMD automation.
OGN-SMD fuseblock can be surface mounted with 5x20 mm pre-loaded fuses, eliminating need for mounting block, fuses, and cover in separate steps. Heat-resistant UL 94 V-0 plastic withstands heat of vapor phase and reflow soldering. Fuseblock is rated to 10A/250V. Rated power acceptance at ambient air temperature, with or without reflow cover, is 4W; with transparent cover, 2.5W. Pin spacings of...
Read More »
Fuseblock facilitates installation in SMD automation.
OGN-SMD fuseblock can be surface mounted with 5x20 mm pre-loaded fuses, eliminating need for mounting block, fuses, and cover in separate steps. Heat-resistant UL 94 V-0 plastic withstands heat of vapor phase and reflow soldering. Fuseblock is rated to 10A/250V. Rated power acceptance at ambient air temperature, with or without reflow cover, is 4W; with transparent cover, 2.5W. Pin spacings of...
Read More »
Fuse Blocks provide Type 2 motor-starter protection.
Class CC fuse blocks are molded in self-extinguishing polyester fiberglass, and offer touch-safe operation with no load fuse disconnect lever. Rated at 30A and 600V, they accept wire sizes of 6-14 AWG. With CC fuses, units carry motor starting inrush currents, providing current limitation to protect against low and high level faults. Fuse blocks are UL listed, cUL certified and carry CE mark.
Read More »
Fuse Blocks provide Type 2 motor-starter protection.
Class CC fuse blocks are molded in self-extinguishing polyester fiberglass, and offer touch-safe operation with no load fuse disconnect lever. Rated at 30A and 600V, they accept wire sizes of 6-14 AWG. With CC fuses, units carry motor starting inrush currents, providing current limitation to protect against low and high level faults. Fuse blocks are UL listed, cUL certified and carry CE mark.
Read More »
Safety Block System prevents stamping press operator injuries.
Lightweight 6061-T6 aluminum safety block is used during changeover and maintenance of die components to prevent injuries to press operators. It has compressive yield strength of 35,000 psi. Wedges compensate for gap left between safety block and upper press section ram. Optional power cutoff plug can be connected to press operation control circuit.
Read More »
Safety Block System prevents stamping press operator injuries.
Lightweight 6061-T6 aluminum safety block is used during changeover and maintenance of die components to prevent injuries to press operators. It has compressive yield strength of 35,000 psi. Wedges compensate for gap left between safety block and upper press section ram. Optional power cutoff plug can be connected to press operation control circuit.
Read More »
Simple Connection – MGB with EtherNet/IP
The new MGB with EtherNet/IP is a leap forward in access door safety. Designed for easy installation, flawless performance, and long service life, it is engineered with robust features and cutting-edge technology that places it firmly at the leading edge of the door safety device industry. To learn all about the benefits of the Euchner MGB, see our video.
Read More »
