Vertical Travel Positioner features rack and pinion mechanism.
Model ZKB20 Z-Axis Simplified Adjustment Unit is used to make up-and-down height adjustments in various positioning devices to prevent misalignment due to shaft rotation. Rack and pinion feed mechanism allows adjustments via rotation of handle. Available in various lengths to accommodate travel distances ranging from 70-170 mm, rugged, scaled post, vertical travel positioning system is...
Read More »Mpact-® Downhole Motors Sets Another New Drilling Record
Mpact-® Downhole Motors Sets Another New Drilling Record Conroe, Texas - Mpact-® Downhole Motors is proud to announce that it set another new Barnett Shale Drilling record on March 11, 2011 using an Mpact-® Downhole Motor. The field performance record was for the longest single-run curve & lateral section. The assembly kicked-off at 7600 feet, and drilled 7392 feet through the curve and...
Read More »
Condition Monitoring System reports imminent hydraulic hose failure.
Designed to continuously monitor health of hydraulic hose assemblies, LifeSense(TM) hose detects when hose is nearing end of its useful life rather than estimating or predicting when hose will fail. Alert is then sent to user so assembly can be replaced to prevent downtime. Single monitoring unit can handle input from multiple hose assemblies. Unlike maintenance programs that replace assemblies...
Read More »
Single-Axis Linear Stage targets space-constrained applications.
SLP Acculine series incorporates linear shaft motor into all-inclusive stage to facilitate transition from traditional linear motion systems, including ball-screws, belt and chain drives, and pneumatic actuators. Intended for applications with limited space low-profile product integrates shaft support within housing and is engineered to have minimized dead zone. Offering sub micron resolution,...
Read More »
A Guide to Quality Control of the SMT Process
The printed circuit board (PCB) manufacturing process begins with cutting-edge equipment capable of accurately picking and placing up to 40,000 components per hour. This innovative equipment keeps error rates extremely low, and those defects that do occur are quickly caught by sensitive laser and optical inspection equipment.
Read More »
Floor Covering Remover strips away difficult materials.
Used for removing tough floor coverings, CTS12 Rip-R-Stripper(TM) acts as tool carrier for electric-powered breakers with ratings from 30-45 lb-ft of force. Direct-impulse force supplies power needed to break through bond strengths of mastics, glues, and thin-set materials. Designed for maneuverability, control, and visibility, configuration lets users operate electric-powered breakers in upright...
Read More »Essemtec to Introduce Paraquda Pick-and-Place at FIEE-ElectronicAmericas
Essemtec Brazil announces that it will introduce the new Paraquda SMT pick-and-place system to the South American market at the upcoming FIEE-ElectronicAmericas exhibition, which is taking place from March 28 to April 1, 2011 an the Anhembi Exhibitis Pavilion in Sao Paulo. Paraquda is one of the world's most modern SMT pick-and-place systems, developed to place all current and future SMD...
Read More »
Digital Indicators support 2 point difference measurement.
Featuring gasketed case, crystal, and stem assemblies, Ã-µMaxum II Series resists fluid contamination. Resolution is selectable in increments down to 0.00001 in. to accommodate application requirements. Two point difference measurement allows comparison of different readings or calculation of measured values. Multiple Factor for ratio measurements allows chordal-type measurements, useful for...
Read More »Speed-Controlled Heating Circulator uses ECM technology.
Featuring spherical motor design, ecocircÃ-® pump uses ECM (Electronically Commutated Motor) technology to conserve energy while delivering hot water throughout commercial or residential properties. Control modes include auto for automatic proportional pressure control and vario for stepless speed control with constant curve. As sole moving part, rotor/impeller magnetically balanced on...
Read More »
Digital Weight Indicator withstands high-pressure washdowns.
Housed in IP69K-rated, watertight polycarbonate enclosure, 190 STORM withstands temperatures up to 176Ã-
Read More »GE Oil & Gas Subsea Equipment Selected to Meet Extreme Requirements of North Sea Gas Field Extension
ABERDEEN, SCOTLAND, UNITED KINGDOM- GE Oil & Gas has received a $7 million contract from Total E&P UK Ltd of Aberdeen, Scotland, to supply drilling and production equipment for the expansion of the Elgin Franklin gas field in the North Sea. To meet the extreme well pressure and temperature demands of the project, GE is supplying surface wellhead and flow control equipment that can operate at well...
Read More »
Custom Fabrication & Machining Services with Over 30 Years of Experience
As a trusted manufacturer to customers across a broad range of industries, Key Gas Components is a premier provider of CNC machining and tube fabrication. Our entire organization is quality driven and customer-centric, with broad-based manufacturing capabilities that can accommodate the most challenging requirements. See our video to learn more.
Read More »
