Micrometers

Micrometer measures depth of surface features.
Micrometers

Micrometer measures depth of surface features.

Digital Optical Micrometer, Model 8400K evaluates severity of mechanical damage such as scratches, corrosion pits, or blemishes that are difficult to observe by other methods. User focuses on good surface near scratch or pit, sets display to 0.0000 in., then focuses into bottom of scratch or pit and reads depth on digital display. RS232 serial port allows data export to included...

Read More »
Thread Gages are suited for deep holes.
Profile Gage

Thread Gages are suited for deep holes.

Able to be used at depths that exceed hole diameter, Multi-Ball(TM) products inspect screw threads for size, location, concentricity, or runout. Thread micrometer measures size, taper, and out-of-roundness of threaded holes for most sizes up to 1 in. dia. Location gage determines location/orientation of threaded hole axis using expanding pattern of balls that come into contact with thread flanks...

Read More »
Laser Micrometer System measures easily damaged parts.
Micrometers

Laser Micrometer System measures easily damaged parts.

LaserMicro100 measures outside diameters and dimensions of shafts, rubber rolls, and cylindrical parts. Able to be used as stand-alone measuring device or fully integrated into automated manufacturing line, unit has repeatability of ±0.2 Â-µ at linearity of better than ±1 µ over its 0.02-4 in. measuring range. Non-contact, single-focused beam system is virtually...

Read More »
Measuring Heads suit tube, pipe, and profile production lines.
Miscellaneous Gages

Measuring Heads suit tube, pipe, and profile production lines.

Using non-contact measuring technology, ODAC® measuring heads monitor OD, Out of Round Condition 24/7, and provide continuous information on overall performance of mill. Product diameters from .004-11.81 in. can be measured with repeatability up to ±.000008 in. Gauges are available in single plane or integrated dual-plane X-Y versions. Air curtains, cooling blowers, and enclosures...

Read More »
Optical Micrometer uses built-in CMOS camera.
Micrometers

Optical Micrometer uses built-in CMOS camera.

LS-7030M Optical Micrometer makes high-speed measurements of fast moving targets on production and assembly lines via high-intensity, low-noise GaN LED light source. It generates continuous 30 mm wide beam with no gaps in detection due to scanning. CMOS camera in receiver head of Optical Micrometer provides image of target on Controller Monitor. Unit provides 2400 samples/sec, display resolution...

Read More »
Gages simplify threaded hole inspection.
Profile Gage

Gages simplify threaded hole inspection.

Multi-Ball(TM) thread-inspection products allow hardened balls to be used as thread-flank contact elements. Free-floating balls can be positioned at any location on thread. Turning of knurled thimble or pin expands balls into contact with thread flanks. Multi-Ball(TM) micrometers measure size, taper, and out-of-roundness of threaded holes. Multi-Ball(TM) location gages determine location and...

Read More »
Laser Micrometers provide measuring range of .25 to 90 mm.
Micrometers

Laser Micrometers provide measuring range of .25 to 90 mm.

Takikawa LDM Series non-contact laser micrometers include Models 303H and 304H which can measure length, width, height, position, thickness, gap, and inside/outside diameter accurately to within ±2Â-µm linearity with 0.1µm resolution. Model 303H offers measuring range of 0.25 to 30 mm, while Model 304H features measuring range of 0.5 to 90 mm. Both come complete with display...

Read More »
Micrometer measures workpieces without contact.
Micrometers

Micrometer measures workpieces without contact.

Desktop Laser Scan Micrometer offers scanning speed of 226 m/s for inspection of small, high-temperature, or fragile workpieces even during motion or vibration. Measuring range is from 0.5 to 60 mm with selectable resolution from 50 nm to 0.1 mm and repeatability of 0.6 microns. In addition to RS-232C data interface, instrument provides analysis functions including elimination of data...

Read More »
Measuring Instruments accurately read part features.
Dial and Dial Test Indicators

Measuring Instruments accurately read part features.

Outside Micrometers are offered in 0 to 1, 1 to 2, and 2 to 3 in. measuring ranges. Dial Calipers, available in 6, 8, and 12 in. range, provide outside, inside, depth, and step measurements in graduations of .001 in. Also offered: 1 and 0.5 in. Dial Indicator with +/-.001 in. accuracy. Test Indicators have range of 0.008 and 0.03 in. and graduations of 0.0001 and 0.0005 in. respectively. Digital...

Read More »
Dodge® Raptor Coupling Now Available in Three Larger Sizes
Sponsored

Dodge® Raptor Coupling Now Available in Three Larger Sizes

The Dodge Raptor coupling epitomizes the innovation and value that has made Baldor a world leader in industrial electric motors. For almost 100 years Baldor has been the go-to source for industries across the globe. The Raptor coupling is just one example of our dedication to engineered excellence and commitment to providing value and performance. See our video to learn more.

Read More »

All Topics